All Installation Instructions for General Electric Range EGR3000ED1CC

some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

Parts Used:

Top Electrode Mounting Clip

Dana from LEEDS, AL
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

The old burners were damaged by the prior owners.

The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.

Parts Used:

Burner Head - Medium - 9500

Burner Head - Large - 12K

Mohammad from BARTLETT, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Burners wouldn't light

Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.

Parts Used:

Burner Head - Large - 12K

Burner Head - Medium - 9500

Robert from SOUTH ELGIN, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used:

Light Bulb - 40W

Catherine from SEATTLE, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Change bulb

Easy

Parts Used:

Light Bulb - 40W

Louis from LEAGUE CITY, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

burners would not light

Remove the old tubes. Lift the lid NO MORE THAN FOUR INCHES. !!!!! Feel for the connections on the switch ends and attach losely. Carefully ( with some slight bending ) attach tubes to the burners. Tighten all connections. Do not over tighten.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.

Parts Used:

Burner Tube - Left Front

Burner Tube - Right Front

michael from The Villages, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Wrench set

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

gas burners not heating evenly

remove old burner, put new in place

Parts Used:

Small Burner - 5K

Burner Head - Large - 12K

Burner Head - Medium - 9500

Juanita from GAINESVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Front burners had to be lit with lighter

My son lifted up cooktop, unscrewed the front plate to gain access to old tube burners, removed and replaced with new parts.

Parts Used:

Burner Tube - Left Front

Burner Tube - Right Front

Marie from Woodstock, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Broken plastic end caps

repair was easy,couldn't believe I found parts. Bought house with stove in it.wife wanted new one,replaced broken parts cleaned up oven saved 600 bucks.

Parts Used:

END CAP LEFT (BISQUE)

END CAP RIGHT (BISQUE)

eric from reno, NV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Caterers melted the plastic part on our stove

Unbolted the old parts, cleaned the stove, and bolted the new parts on. Looks just like brand new!! The parts were perfect, easy to find, inexpensive, and delivered quickly!
Thank you!

Parts Used:

END CAP LEFT (BISQUE)

END CAP RIGHT (BISQUE)

Kaylinda from Berwick, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Light burnt out.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Parts Used:

Light Bulb - 40W

Roscoe G from ROCHESTER, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Old dishwasher rack and silverware rack

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

Parts Used: