EGR2001EM2SS General Electric Range - Instructions

I took all of the oven racks out , then the bottom cover, over the element. I immediately saw the igniter coil was broken. I took the element out and disconnected the two wires. (I saw that the igniter coil was broken and knew that must be my problem. I got my manual out and found the part number and got on line and started shopping. I found part select, the price was fair and ordered it the same day. It was shipped out to me the same day I ordered it. Received it the next day and had the oven working again. Easy to order, great customer service, fast shipping department. Great job to all of you folks at Part Select. I would recommend PS to anyone that wants to save money and do it yourself. Go for it. tk middlebury IN.

First I took out the old Igniter and discovered the part I ordered did not come with any connectors, just bare wires. This is ok but I found myself searching the stores for the correct attatchments. It would be great if your web site gave the options to order these at the same time. This was my first repair of this kind so I had no idea what I was doing. I thought the part would arrive with what I needed to install it. The hardest part was getting the bolts off the under side of the Igniter. The space if very tight and at an angle that a regular took doesn't really fit. What took so long was taking the bolts off by hand. Im a single woman who likes to try to fix things first on my own. My 18 yr. old daughter was in there with me the whole time learning and finally it was her smaller fingers that were able to get the bolts into the new part. We only finger tightened the part because no tools would fit at the curved angle. I love your web site and the ease of finding the part I needed. Its the stove manufacture who made this project difficult by how they place the screws. I will use them for all my part needs in the future.

Most trouble I had was removing the screws that were located under the bracket. I had to slip the oven door off first to give me more room. Very hard to get to these screws because of where they were located under the bracket. I had to twist and turn the old igniter to get to it. When finally removed, I replaced the old igniter with the new one using my own screws. I twisted the wires together, and replaced the baffles, the oven floor, and then the door. The oven fired up wonderfully! Thank you for your prompt service for getting me the part quickly and correctly.

Removed the two screws that hold the oven bottom to expose the glow element. Also removed the lower draw to get to the connections. The job was only complicated by getting to the two bolts holding the glow plug to the oven frame. Getting them off and getting the new plug on was not easy with standard tools. There was not a lot of room to work the hex bolts and i wound up cutting the old unit out and attaching the bolts to the frame and cutting slots in the new unit so I could slot it in. That worked. The glow plug was the problem and the oven came right on.

I watched the repair video on YouTube and followed his instructions as much as possible. Went pretty well as I thought it would be harder. I’m pretty handy so, I was pleased.

They turned out to be 1/4 inch hex head screws. Only after soaking with penetrating oil could we budge them. There must be a special tool to loosen them on the back side where there is no room to get a socket on them and since they are in the heated part of the oven they are almost welded in. We were successful, but could only get one screw back in. So never use your oven with the door left open as I did if you do not want to repeat what happened to me.

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

I was able to access the burner and igniter by removing the broiler drawer. The flame guard was removed with a nut driver and the old igniter with a phillips screwdriver.

The electrical wires had to be spliced into the old igniter wires as they did not come with the factory connectors. However sire nuts were supplied.

After replacement of the igniter with the new one .. it would glow and about a minute later the gas would come on. However the gas from the burner did not light. I had to adjust the bracket closer to the burner to correct the issue.

Note: The igniter is wired in series with the gas valve. This means that it will continue to glow even after the burner lights durning oven operation.

Remove the front door-lifted off(no tools) removed the floor of the oven (2 standard nuts at the rear). nut driver to remove the igniter. Took longest to untwist and retwist wires & dropped screws. reassembled and tested...worked perfice. this is the 4th time I've used Parts Select and It's great....Thanks and keep up the good work!

This web site is awesome!!! their forum told me what part i needed, and they shipped it out, super fast, i couldn't hardly believe it! I tried using the Sears Parts web site for my "kenmore" oven and that was a joke, seriously! no more kenmore for me, thanks. It took this site to figure out that i really had a G.E. with a kenmore name on it.
I found out that even though the old ignitor glows well, it may not pull enough amps to open the gas valve.
First i disconnected the two wires on the gas safety valve that lead to the ignitor. These are accessed after taking the bottom drawer out. Then using a nut driver, i took out the two screws holding the bottom of the burner tube. Then inside the oven, i took out the racks and then the two screws in the back on the bottom. Then took out the bottom plate. I removed the one screw on the front of the burner tube, and removed the burner tube with the ignitor attached. I cut the wires off the old ignitor and attached them to the new ignitor with the supplied ceramic wire nuts. I attached the new ignitor to the burner tube and put everything back together. The bottom screws on the burner tube were very difficult for me to reach. Almost impossible to get both hands there to do the job.

Remove the broiler pan to get at the 2 nuts that hold the gas burner, remove them and then you can get at the 2 nuts on the back side of the igniter.

My repair was easy. The hardest part was trying to get the 2 small screws off and on the igniter. You need small hands or a small, angled socket set. I did mine with the door of my oven still on and maybe that was why I couldn't reach the screws that well. If you can do the repair with the door off, I would say that would be easier. As soon as the new piece was screwed in, it worked on the first try.

First i removed the inside bottom of the oven where i could get to the actual glow plug igniter and removed the two screw that held the igniter in place. I than pulled the entire oven out allowing me to access the two wires connecting the igniter to the stove. I disconnected the wires and had to splice the wires as to be able to reach the appropriate connections. I reinstalled the igniter and upon testing the igniter worked properly. The entire process took me one hour.

Followed suggestions of previous posts. Removed oven door, warming drawer, pan in bottom of oven. Removed element to replace igniter. One thing I would add is I put a small piece of electical tape on the heads of the two 1/4 in. screws for the rear element bracket. This kept them from falling out of nutdriver.

Start by shutting off the main gas supply to the range and unplugging the electric cord.
You will first need to take the plastic control knobs of from each individual burner (they should slide straight off).
Next, you will need to remove two phillips head screws on the front face of the panel. They are located on the right side of each rear valve burner stem that is sticking out through the panel.
Next, open the oven door, locate and remove the three screws on the bottom of the front face panel. The front panel should now come off exposing the top burner manifold and all of the valve burners.
The next step would be to take the burner grates and each round burner cover off (no tools required). This will expose the top of each individual burner. You will see screws that hold each individual burner down to the stove top. On my stove the heads were all rusted and I could not remove them. If you can remove all four of your burners and disconnect the wire on each ignitor and set the burners aside.
Next, go back to the front of the stove where you took off the panel and you will see two metal clips on each side of the stove top. Push each one of these in with a screwdriver and gently lift up on the stove top. It should hinge up towards the back of the stove and give you full access to the burner valve you need to change.
Next, use a box end wrench (I think it was 1/2") and remove the gas line attached to the burner valve. After the gas line is removed, take out the bolt and clamp that holds the burner valve to the manifold. The old valve should drop out.
Install the new valve making sure the rubber gasket is seated properly, reattach the clamp and bolt and reinstall the burner tube line.
Before you put the range all back together turn the gas back on at the appliance shutoff. Locate the gas orifice for that particular burner and hold your thumb or finger over the hole. Turn on the burner and leak test the burner tube connection and where the valve is clamped into the manifold.
Shut the burner back off if the leak test passes and reassemble the stove.
If your burners won't come out of the stove because the screw heads are rusted off (like mine was), you can carefully lift the lid a couple of inches to gain access to the valve. Make sure you don't bend or kink any of the burner tubes.