All Installation Instructions for General Electric Range EGR2000EM3WW

oven would glow but the burner would not come on

My son took out the old burner bar and there was a hole burnt right through it. I ordered the part on Weds night and was surprised when we received it so quickly on Fri morning. He had no trouble at all - just removed the old igniter and bar and replaced it with the new one. Nothing needed cut or spliced - perfect match. Now I can bake again!!!

Parts Used:

Burner with Igniter

Charlotte from Rochester, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

7 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Replace glowbar igniter

Removed the old glowbar's two screws. Didn't take a mental photo of its proper placcement (or a real one, which would've been smart). Removed screws holding 1) a heat protection plate, and 2) wire harness plate. Installed the new glowbar, hopefully, the right way - with its heat-plate facing the gasline of the over/broiler. Reinstalled the heat protection plate and wire harness plate. Hasn't blown up yet!

Parts Used:

Flat Style Oven Igniter Kit

Daniel from Espanola, NM
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Wrench set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Hard to remove screws & no instructions that a heat shield had to be transferred from old to new

One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

Peter from REDDING, CT
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Over not heating

1. Removed oven door..
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.

Parts Used:

Flat Style Oven Igniter Kit

Chris from Inglewood, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

bottom trim had rusted, so we needed new piece

Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked open!)

Parts Used:

Bottom Trim - White

Robin from Apple Valley, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

we had damaged the burner cap

just removed the old burner cap and put on the new one.

Parts Used:

Burner Cap - Medium

Gary from Indio, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Oven would not heat to the degree you set it for

I first took out the screw which held the bottom plate for the oven. then took the screws off the igniter unhooked the wires , took the new igniter hooked up the wires then put the screws back in put the bottom plate back in and turned the oven on to test it and it worked great.

Parts Used:

Flat Style Oven Igniter Kit

MARY from BIG LAKE, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Burner had uneven flames

Too easy a five year old could do it

Parts Used:

Burner Head - Large - 12K

Akshay from Bridgeton, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Drawer support broke

Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plastic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.

Parts Used:

Drawer Support

Charles from BOULDER, WY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Part will wear out after a couple of years

In my case it was the lower burner so I unplugged oven and turned gas off.
Then I removed the bottom drawer, and the lower burner cover.
Next unplug Oven Igniter, found where drawer existed.
Removed 2 screws attaching Igniter using nutdriver
Placed new Igniter on
Plug Igniter in and tested oven
Replace burner cover and drawer

This was much easier then what I went through with a repair man the first time around. These Igniter are designed for certain model stoves and are not interchangable with other model stoves!!!

Parts Used:

Flat Style Oven Igniter Kit

Richard from Mt Solon, VA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Drawer sticking and not operating smoothly

I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.

Parts Used:

Drawer Support

Bill from Philadelphia, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Broken drawer glider

Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.

Parts Used:

Drawer Glider - Right Side

James from RANCHO MIRAGE, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bottom trim piece on 24 year old stove had rusted. Replace trim piece was still available.

Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.

Parts Used:

Bottom Trim - White