All Installation Instructions for General Electric Range EER2002M02BS

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used:

Light Bulb - 40W

Catherine from SEATTLE, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Not Reaching Temperature above 300 Degrees

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

Parts Used:

Temperature Sensor

Ron from SAN TAN VLY, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven was very slow to heat

Removed the rear panel from the Range using the nut driver. pulled the terminal wires off the back of the heating element. Double checked if there was continuity across the heating element terminals before removing the element. If there is none, its bad. remove the two screws inside the oven holding the element in place. Once free, lift the front of the element to about 30 degrees and pull towards you. Insert the new element in the reverse manner then secure it using the two screws. Push the terminal wires onto the terminals on the back of the element and reinstall the rear panel.

Parts Used:

Bake Element - Push On Terminals - 240V

James from CANAL FULTON, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Bake element was burnt out.

1.Disconnect the power cord. 2.Remove two screws pull the element out. 3.Disconnect the wires attach to element. 4. Install the new element connecting the wires. 5. Align element with holes and tighten screws. 6. Plug in power cord and begin to cook.

Parts Used:

Bake Element - Push On Terminals - 240V

Bertram from ABERDEEN, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

oven door gasket needed replaced

Ordered the part, it arrived and 5 minutes later it a complete installation

Parts Used:

Range Oven Door Gasket

Mary from LONGS, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Bad Line fault displayed on range clock

1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.

Parts Used:

CONTROL OVEN TO9

Vincent J Paola, from GREENWEL SPGS, LA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Baking element broke

Opened the box removed old element with socket put new one in tightened and voila ?? Just in time for thanksgiving ??

Parts Used:

Bake Element - Push On Terminals - 240V

Veronica from PORT ORCHARD, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

oven wouldn't heat

removed two screws that hold the element in place and then removed the access rear panel it was much easier to disconnect the element than have to stick my head in the oven to gain access.time :15 minutes.

Parts Used:

Bake Element - Push On Terminals - 240V

JEAN-C. from PARRISH, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Knob part broke on & off switch.Got a nee

Got a new knob.

Parts Used:

Knob

Sandra from Saint Johns, AZ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven board went out

One wire at at time then used my razor blade to get front off stuck right back on

Parts Used:

CONTROL OVEN TO9

Jackie from TICKFAW, LA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven heater coil burned out

Removed power plug- disconnected wire, removed cover over wires two screws, and removed old heated strip, held in by two screws inside of oven
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success

Parts Used:

Bake Element - Push On Terminals - 240V

David from Canterbury, CT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Replaced oven door gasket

Remove old stained gasket and replaced with new. Only $57.00!

Parts Used:

Range Oven Door Gasket

Paul from JACKSONVILLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Lower heating element broke and burst in flames

On the website, the heating element looked exactly the same with same measurements as the old one. However, the part I received did not match. The screw holes where the element attaches to the back were wider apart and higher. Plus, the leads curved up instead of being straight.

Parts Used:

Bake Element - Push On Terminals - 240V