EE2107WT Speed Queen Dryer - Instructions

removed old element, relaced with new element , thermostat dryer works better than it has in along time

UNPLUG Drier
Remove bottom panel 2 screw
Remove 2 connector to coil
remove 2 screws
lift off cover
lift coil s
reverse steps

Unscrewed the front and ran the dryer. The heating coil DID get red hot but the gas DID NOT blow out. Unscrewed the cover over the top of the two coils. Disconected the wire. Replaced coil and cover. SUPER EASY. Its the starting and holding coil which lets the gas shoot out onto the heating filament. $75.00 just for the repair man to come out plus parts, plus labor. Probably saved $200+. All the prints of the parts are on the website so you can see what your changing. TRUST ME....DO IT YOURSELF. You'll be glad you did!!

I took the front of the dryer off. The two gas valve coils were right in front. Replaced the two terminal gas valve coil and the secondary coil valve three terminal. Cleaned the inside with shop vac and re-installed the front dryer panel.

removed cover removed old coils installed
new coils ,test dryer running great .
thanks partselect.

I took the front dryer panel off by removing 4 screws. I the removed 2 screws from the bracker that secured the 2 valve coils. I unplugged the 2 coils the placed new ones in the exact same position. Fastened the valve coil bracket and replaced the front dryer panel. The dryer worked like new. Thanks!!!

The first thing to do is to check to be sure the vent is clear. The easiest way to see if this is the problem is to pull the dryed away from the vent and let it vent into the room. Once you have determined that the vent is not the issue, take the front cover off and see what is going on on the inside. To remove the front cover first remove the 4 screws on the inside of the upper cabinet to take off the control panel, I was able to gain access to the screws under the front of the control panel that hold the front cover in place. A couple of electrical connectors later the cover is removed. The coils are easily accessed from in front of the burner by removing the 2 screws that hold the small silver cover over the coil. Once the cover is removed, the coils slide off a short shaft and you can replace the coil by swapping the apporpriate electrical connector for the coil being replaced. The coils are alligned with a small white pin so you can't get it wrong. Replace the covers and fire away.

This repair is easy and saves you a lot of money. This is a great web site, easy to identify the parts you need and the delivery is very fast. Nice Job!!!

The diagrams listed online gave me a the information needed to trouble-shoot which part could be broken. It only took two tries to see which part was out but was significantly cheaper than a repairman. The expediant delivery on parts made down-time a minimal. Very pleased with results.

First, unplug power. The coils are easily accessible from the front of the dryer. Use a 5/16 nutdriver to remove two screws at the bottom of the bottom panel and lift the bottom edge of panel toward you. Pops right out. The assembly with the coils is on the front left. Use a small phillips to remove the coil-retaining bracket. Keep track of orientation of which coil goes where. Slide the suspect coil up off the column and slide the replacement in its place. Carefully slip off wire clips from old to new coil. Repeat for second coil. Reassemble and test.

Igniter would glow and flame would burn for about 30 seconds then a rattling noise would start and the flame would go out. Replaced the coil and all is well. Very simple and inexpensive. One of the easiest repairs I've ever done. Video was very helpful.

Both washer and dryer always worked perfectly. Suddenly, dryer wasn’t drying laundry properly. Problem... no heat. Cheapest price I could find calling for appliance service was about $160 to replace coil set but no one would tell me this would fix the problem. This was after calling a number of repair firms and trying to get a somewhat close estimate of what my problem was and what the repair cost. Not knowing, I might have just paid the $160 but what turned me off was having a service call fee of anywhere from $50-$80 with no one willing to tell me what the problem might most likely be before coming out or give me an estimate over the phone other than a range of $160 - $275. I just did not want to have someone come out for $50 -$80 and tell me that I needed to spend $275 and still owe them the service call even if I did not agree.
Found diagnostic and repair instructions help on line. The diagnostic information indicated a high probability, roughly 50%, that replacing the coil set would solve the problem and found the coil set cost $19.21 plus shipping, so I ordered the coil kit for total of $26.70. Note... I am a 71 year old amateur never having worked as a repairman of any kind except for my own needs.
The repair itself took less than 30 minutes start to finish and was one of the most straight forward, glitch free, easy repairs I have ever done. This is a gas dryer but still uses 110 power so I unplugged the 110 power cord from outlet. Followed suggested guidance on opening the dryer cabinet from the front and presto, the coil set I needed to replace was immediately right in front with easy access. Removed 2 screws for the hold-down bracket, slipped off both coils, one at a time, removing the wiring connection for each coil and then reconnecting to each new coil before slipping each new coil back into place and reattaching the hold down bracket. Reinstalled the dryer door and cabinet front in reverse order from taking off... 4 screws total. Plugged in the 110 power cord and put in a damp load of freshly washed laundry. Presto... 30 minutes later... dry laundry. Note... could do the same repair again in half the time since I took it slow and careful 1st time and also took time to remove dust before completing repair. I like things to look like new inside and out and it did when I was done. $26.70 and good as new. Why I didn't spend $160 - $275 is pretty obvious now.

Downloaded a schematic of the dryer controls. Watched a UTUBE video of how to remove the front panel of a Maytag Performa dryer. It was pretty easy. Consulted your website and found out that bad coils are typical of the symptoms 46% of the time. I have bought parts from you before and happy with results.

The gas would light briefly then go out so the clothes were never heated. I googled the problem and found your website and read a few blogs describing the problem, ordered the coils, popped them in and presto it worked.

I replaced gas coils which in my case came as a set and that did the trick.

Pretty much just followed the installation video. Took dryer apart and just put everything back the way it was.