EDW2060F03SS General Electric Dishwasher - Instructions

after I let the unit rest on its side to expose the bottom part, I took a picture just in case for reference; I marked all electrical connections, so it would go to right place into the new unit; removed the old pump unit by loosening the rubber clamps, for the inlet and outlet; detached the support sling for the motor unit; installed the new pump unit; it fits like a charm and it was wonderful; I had some bad experiences of replacement parts from other suppliers, on many things that I fix , that won't really fit like the original, but this one fits like a charm; I made my first test run with just water with out the detergent and after one cycle I used the necessary dishwasher detergent and it works just like brand new; Thank you, PartSelect, I will be ordering any of my part needs from you. - G.V.

A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.

Removed filter screen with the socket set, removed the piston and nut assembly with pliers, and installed the new piston and nut assembly. Put filter screen back in with hex head screws. During the process, I opened the float regulator and cleaned it out too. Water backup problems solved.

First I removed the bottom dishwasher rack. Using a 1/4" nutdriver I removed (4) 1/4" screws from the drain cover that is inside the dishwasher all the way in the back. This will allow you to get to the piston and nut assembly which was easily removed with no tools by simply grasping and unscrewing. Used a wash cloth to wipe "gunk" from around the threads. I then screwed the new piston and nut assembly in place. Used no tools to tighten, just "snug up" by hand. The seal on my old piston and nut assembly was 50 percent gone, not sealing at all. I guess the years had taken their toll. This solved my problem. The dishwasher washes and drains as it should. Super easy fix. Took me about 10 minutes to do the repair.

Removed filter/screen by unscrewing 2 screws with a nut driver and then unscrewed the old Piston and Nut assembly and simply screwed in the new part. Problem solved and my dishes are much cleaner and the water is draining out completely. Easy fix for this frustrating problem.

Followed the simple instructions to unscrew the old unit and replace with the new one. The unit was easily located on a diagram on the internet and the website instructions for removal were spot on.

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

I Just Open Door And Put Fill Cap In And Turn That It

First I opened the dishwasher and removed the lower basket. Next I removed the 4 screws that hold the food filter plate in place at the back of the tub. Then I unscrewed the Piston/Check Valve assembly counterclockwise, located at the back center of the tub, by hand. I replaced the old part with the new one and reinstalled the filter plate. I ran a rinse cycle to verify that that all of the water was purged. Finally, I reinstalled the lower basket and resumed using my dishwasher.

First let me say, it's so easy even a caveman can do it. I removed the water out of the bottom. Then I removed the cover in the very back of the machine with a wrench. As soon as I did that, I could see the piston. Next, I twisted the white piston out with my fingers (this was the hardest part). I could see the piston had partially disintigrated. I ordered a new one, had it delivered in a few days, and put it all back in reverse. It took minutes. Thanks to the guy that posted his story, I was able to fix mine for $18.

Just remove the 4 screws at the lower rear inside the washer to remove screen holder...then unscrew the Piston and Nut Assembly by hand. Put in the new unit, reattach the screen holder with the 4 screws...and the job is done. Probably takes less than 5 minutes....very easy.

I measured the diameter of the working wheels from the existing ones, and located the parts I needed from the website. I order two packages, each containing the wheels and axles for the rack.
When delivered, I snapped the wheels onto the delivered axles. Then, I snapped the axels unto the bottom rack, at the correct place. I used a large pliers for leverage because the axel was a bit tight to just simply snap on.
The middle wheels are located just behind the front wheels, thereby offering support when the botton rack is pulled forward for loading. Likewise, they offer support when the rack is pushed back in place.

Just remove the lower basket from the machine and pull the old wheels off. Then snap on the new wheels on the pegs. The old style wheels snap in place without much force. The new wheels take much more force to install and lock onto the basket which keeps them from coming off when the basket is heavily loaded.

Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!

The most difficult part was removing the old wheels. The plastic coating on the rack had come off, leaving the metal exposed. The wheels had rusted on - that's why they wouldn't roll. Once we got them off with pliers, hammer, screwdriver and basically everything in the tool chest, we were home free. Installing the new wheels and axles was easy.