EB9FVHXVQ02 Whirlpool Refrigerator - Instructions

Herbert from MAHOPAC, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

FREEZEING UP

in stalled new circuit board an thermostat an was fixed

Parts Used:

Sherril from ROBBINSVILLE, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator would stop cooling intermittently, control panel would not display temp settings until power was reset.

The video on the part select website with the Canadian gentleman was absolutely the best! My wife and I watched it and was able to accomplish the replacement with no surprises or issues. One tip that we could add is that the orientation of the temperature sensor was not specified in the video, but the slot seemed to work better for one orientation versus another. It has been a couple weeks since the repair and the refrigerator is working like it did when we first purchased it.

Parts Used:

Jim from HALTOM CITY, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The drawer glides were broke.

Couldn't have been easier. Took around 5 minutes. All you have to do is remove 4 Phillips head screws, put on new drawer glides, put the screws back in and your done.

Parts Used:

Greg from WAKEMAN, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

broken drawer glides

removed the shelf, unscrewed 2 screws in each side. Removed broken glides and installed new ones in the reverse order..

Parts Used:

John from JONESBOROUGH, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

After 19 years of use, both side glides of deli tray had cracked.

Just 2 screws on each side - took them out, installed new glides with existing screws.
Very easy - ended up giving the fridge a thorough cleaning - fridge cleans so easy and quickly.

Parts Used:

Liz from ELMHURST, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken Draw Guide

Simple! Remove and replace two screws.

Parts Used:

Clayton from DUVALL, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Refrig. was not holding proper temp in refrig compartment

Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.

Parts Used:

Dan from Goldens Bridge, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken drawer slide

Extremely easy. Probably could have been done with eyes closed.

Parts Used:

Irvin from Louisville, KY
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

ICE BUILD UP AT BOTTOM OF FREEZER

DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.

Parts Used:

Grommet

Gerald from COLORADO SPGS, CO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

the freezer and refrigerator number would lower it self and eventually get to "-" and "-" essentially shutting it self off!!

I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..

Parts Used:

Marc from SEASIDE, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Freezer not defrosting and making fridge run warm.

Super simple following the instruction video you posted. Thanks!

Parts Used: