DWU5902AAM Maytag Dishwasher - Instructions

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

We had tried to use dish washer cleaners, and they would work for a time, but we started spending more money on cleaner than we wanted. I ordered and then I replaced the lower spray arm. It took a little effort to get the top screw off, due to hard water deposits. The new one went on very easily, just screwed right in like the old one. It's working great and I really don't mind not getting a new one or paying for a service call!!!

received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.

First I removed power to the dishwasher. The inside panel of the dishwasher door is held on with several screws with Phillips heads. Remove those and the panel comes off. There is a silver metal guard that you have to pull off being careful not to tear the insulation that is on the other side. Then there is one hex head screw to take off the handle latch assembly. You remove this assembly and take off the wires to the two switches on each side of the assembly. The replacement part doesn't come with the black plunger that pushes on the switch buttons so you have to remove it from the old assembly. This was the only difficult part, I essentially destroyed the old plastic assembly getting it out. But putting it in the new assembly was easy. Then I attached the wires to the switches in the new part and reassembled everything. Works like a charm now.

First I replaced the door gasket as every one else. This cut drips about 30%. I then discoverd that the Rinse Aid circular dispenser cap was opened about half way. I turned the cap tightly clockwise to close and cut drips to 90% total. I czn live with the other 10%,

The repair was very easy! I simply pulled out the old gasket from around the front part of the dishwasher. I cleaned the area with a damp rag from any residue that was left on. I bent the long gasket in half and and pushed it in starting at the center of the dishwasher and went down one side at a time until the whole gasket was in. I then ran a short cycle on the dishwasher to make sure it was properly in place and the problem was fixed. NO MORE WATER ON THE FLOOR! I was so very happy to know my problem was fixed and I didn't need to buy a new dishwasher! It's been running great! :) ~ Elizabeth ~

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

Followed the instruction video provided by this site ! 15 minute repair?..Super Simple!!! I Love this company!!! Saved me a bunc of money!!

My husband thinks I'm the smartest wife ever! He's telling all his friends how I got online to research the problem (thanks to your readers and DIY comments!), diagnosed it, ordered the parts and - voila - clean dishes once again! It's like everyone said, remove inside of the door by removing 7 torx screws, dismantle wiring -remember to note what connects to what - pop out old parts, easily insert new ones (that arrived in record time!), reconnect wiring, replace door and you're done. Replacing the reservoir o-ring also stopped the leaking problem that preceded the door issue. Thanks PartSelect!

I didn't know how to put in the new one clips until I looked up a picture of them in place, on-line. Once I saw the picture, it was a matter of clipping the new ones in place.

I first made sure the new gasket was long enough and it matched the original. Next I used the tip of a screwdriver to pick out a corner of the old gasket and then pulled the entire thing out. I noticed the old one stopped at the bottom of the gasket well. The new one was much longer and I thought I might have to cut it to length. Well I'm glad I didn't. If you start on the right side and work your way up and around with a 2 in. piece longer then what the old one was. I carefully tucked it in the bottom and closed the door. Glad I didn't cut the new one. Instructions would have been nice. Overall an easy fix. I'm very mechanically inclined so I knew better.

After pulling dishwasher out both springs easily installed using plastic connectors on the bottom left and right sides. Pliars were used to stretch the springs. It took fifteen minutes at most.

New pump housing filter was needed as the old one was plugged and distorted.

I

Removed door interior, confirmed with tester that power was reaching door cut-off switch, but not power on other side of switch when engaged. Noticed that little switch button frozen in shut position, assumed switch had burned out. Installer new door cut-off switch with new (dual) switch units in place, plugged in unit and it ran perfectly.