DU588 Jenn-Air Dishwasher - Instructions

Remove bottom cover.
Put the belt on the large pulley and stretch it about 5 times to make it larger. Remove the belt from the large pulley and put it on the small pulley at the motor. Stretch it to left side of the large pulley and make sure the belt is on partial of the pulley's groove then rotate the large pulley forward. The pulley will pull the belt into the groove by itself.

Pull old gasket off (30 seconds), take panel screws out of front panel and control panel, carefully lower control panel push tabs thru holes from inside door, once all tabs in, push door closed and take pliers and pull tabs until they lock into place, put panel back together. not that difficult, my wife and I had it back in working order in approx 30min.

Put spring in plastic bushing, snapped into door arm and hooked opposite end of spring in first hole. Repeated process on opposite side of door. Did the above without moving the dishwasher from installed position.

Belt seemed too small at first to fit, but turning the power module pulley while holding the belt enabled it to slip in properly. Didn't help that there's not much space to work.

On my maytag portable dishwasher I had to remove three side screws on right lower panel,and two lower screws to free up panel. I had to pry the panel away from the body to get axes to the springs. Replaced springs as instructed reinstalled all hardware, finished.

I opened the door and pulled the old gasket out using a flathead screwdriver to pry up the difficult to remove areas. I cleaned the area with a damp cloth and place the new gasket in the slots. The entire process including the cleaning took no more than 10 minutes. It was so easy. By the way, I had the part in my hands 2 days after ordering it. I am very impressed with the service.

had to pull the unit out abour 6" and simly replaced the springs - it was easy

Removed the front of the door by removing 2 screws in each side.

Remove 2 screws on each side holding control panel

Removed old gasket by pulling it out, and installed new gasket. Used needlenose pliers to pull tabs securely into slots.

Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.

The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.

Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.

Unscrewed the diswasher from the counter, pulled it out to access the right main door spring and took out the old spring.I installed the plastic washer then slipped the spring throught it and pulled the spring donw with the needle nose vicegrips and inserted the bottom of the spring into the lower hole. I pushed the dishwasher back andrefastened it to the counter.

I removed four screws and thus the front plate at the bottom of the dishwasher. I then removed the old spring, using a long nose pliers and, still using the pliers, replaced it with the new one. The enclosed instructions were helpful as was the previous letter written by someone with the same problem. I then replaced the bottom plate and the door worked as it should. Thanks for once again having the part I needed.

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

First I was amazed that the belt was available for my ancient dishwasher. Then I was amazed again when it came overnight. The instructions said to stretch it over the two pulleys but my hands weren't strong enough. In a sudden flash of brilliance I decided to use a screwdriver as a lever to force it onto the second pulley. Done deal - happy home handyman.

I was not able to follow the instructions exactly since they called for stretching the belt around the back pulley with the left hand. For a woman that prooved too difficult so instead I attached the belt to the back pulley first and used 2 screw drivers (they are thin) to stretch the belt around the front pulley. It took considerable effort but I got it on!! The dishwasher now works. Praise God!!

Clip the plastic on to the vertical pieces. No tools needed