DU2J Magic Chef Dishwasher - Instructions

Removed 7 Torx Screws ... removed inner door panel ... snapped off the selinoid after noting the exact original position ... removed the Latch assembly 2 hex head screws ... removed the old Grommet which was crumbling apart ... stretched the new grommet in place. Then did the steps in reverse to complete a successful repair.
Thanks to your website, quick turn-around service and customer's repair stories, I probably saved a few dollars but mostly, I realized how much I love my dishwasher now more than ever!

Attempted repair was quick & simple. Removed 7 torx screws, and then pulled the wax motor out of its holder. Pulled 2 wires off, and replaced old motor with new motor. Reattached wires, & reassembled.
Only problem was this did not fix the problem, so back to square one, but worth a shot.

Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.

Once I removed the inside panel from the door replacing the switch was pretty simple. completed the job in less than twenty minutes.

This was the third appliance I have repaired with the help of Parts Select in the last three months.

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

I removed lower cover panel. Removed two wires. (one on each end of the element. Removed two nuts on the element. Took out old part. Put new part in and reversed procedure. Works fine now.

First I replaced the soap door grommet -- door still leaked. Then I went for the really expensive part ($40) -- the door gasket. The old one came right out and the new one went right in -- 15 minutes tops -- and the door no longer leaked.

Thanks to all the previous posters for their hints.

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Initially thought this issue was the dishwasher door gasket, but after reading post on this site about door latch grommet, removed 7 "hex screws" pulled inside of dishwasher door away and traced water from leak back to soap dispenser latch/grommet area so instead of ordering door gasket ordered door latch and grommet. Replaced grommet only (in addition to 7 "hex screws" had to remove 2 additional screws to get to it) which took some maneuvering. Re-aligned grommet and latch, inserted and tightened all screws that had been removed. Works great - no more water leaking!

Followed the instruction video provided by this site ! 15 minute repair?..Super Simple!!! I Love this company!!! Saved me a bunc of money!!

The repair was very easy! I simply pulled out the old gasket from around the front part of the dishwasher. I cleaned the area with a damp rag from any residue that was left on. I bent the long gasket in half and and pushed it in starting at the center of the dishwasher and went down one side at a time until the whole gasket was in. I then ran a short cycle on the dishwasher to make sure it was properly in place and the problem was fixed. NO MORE WATER ON THE FLOOR! I was so very happy to know my problem was fixed and I didn't need to buy a new dishwasher! It's been running great! :) ~ Elizabeth ~

I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

Remove the motor and impeller housing assembly from the unit by disconnecting the motor wiring plug, green ground wire, removing the drain and transfer hose, wash arm assembly and three screws for the filter assembly. A plastic locking ring secures the housing assembly into the unit and is removed by rotating aft about an eighth turn. The impeller is removed from the motor shaft by unscrewing the left hand threads on the fan that attaches to the end of the impeller. The impeller has longitudinal splines that engage the motor shaft, so it has to be removed by pulling straight off of the motor shaft. My impeller was stuck on the motor shaft, so I used a dremel tool with a cut off wheel and sliced through the impeller to loosen it. Installed a new motor shaft oring, and then slid the new integrated seal/impeller onto the motor shaft and secured with the fan (remember left hand threads). Reassembled unit and no leaks...

I went to take the bottom front panel off and ended up dropping the screw down behind the baseboard and then found that I did not need to take the panel off. The broken end of the float was not obstructing and I was able to just drop the new float in place. I spent more time looking for a replacement screw than any thing else. Ran it and it works fine.