DU2J-CAN Magic Chef Dishwasher - Instructions

Removed front access panel
Disconnected water supply
Pulled dishwasher out approximately 1 foot to gain access to spring linkage
Connected new spring linkage to spring, connected other end of spring linkage to door
Tested operation of door
Slid dishwasher back into place, reconnected water supply and front access panel

just pulled out old gasket
pushed in new one

Turned off the water. Disconnected the water supply line. Extracted 2 screws holding the dishwasher. Pulled out the dishwasher. Changed out the nylon spring link. Pushed the dishwasher back into place. Reattached the water line. Turned the water back on.

Spring linkage and postage about $15.00.
Savings on service call and parts about $175.00. What a deal. Thank you PartSelect.

I took off the pump cover, removed the broken part. The support was broken at the threaded area so I needed to remove both pieces. Then I just used the diagram to see how all the pieces fit back together. I always take a picture too just in case I don't remember how it should go back.

Super easy repair.

removed the 2 stops that held in the upper basket. rolled the old one out and slid the new one in. the replaced the stops. cake and pie!!

I first replaced the seal/grommet around the soap dispenser latch, which was leaking, but did not totally stop the leak. I ended up ordering the door gasket too. Both were very easy to replace. My wife wanted a new dishwasher, but let me take a crack at fixing the leak first. Woo Hoo - big $$$ saved.

The problem would rarely happen if the dishwasher was fully loaded vs. lightly loaded; which would produce a lot of water rapidly during the spray cycles. (or empty during the house inspection!). Removing and replacing the door gasket is super-easy.

Un screwed the dishwasher from the underside of my kithcen counter. Removed the copper water hose(after turning off water valves). PUlled the dishwasher from under counter to expose the hinges. Hung the new linkage on the hinge. Stetched the spring from flange on the bottom of the dishwasher to the new linkage. Reattached hose and reconnected the unit to counter top. Job done.

I removed the gasket from the packaging & soaked it in hot water for approx 5 minutes to enhance the pliability of the rubber. I them opened the dishwasher door and removed the existing gasket, making sure I observed any specifics of the gasket, (ie...shape of gasket). I then cleaned any debris from the gasket channel. I took the new gasket from the water and folded it in half to determine where the middle was, and I started inserting the gasket beginning at the middle area of the channel, (just under the door latching mechanism). I finished inserting both sides and then closed the door for approximately 30 minutes to complete the gasket seating process. No leaks!!!

popped the two end caps off of the runners (the hardest part of the installation was figuring out how to pop them without braking them). Turns out just using a flat screw driver to start opening the cap lock did the trick. Once the end caps were off it was just a matter of rolling the old one off and the new one on and then putting the end caps back on.

The new basket wasn't an exact match, it's lighter weight and doesn't have the exact same configuration as far as the rows of tines. This will do us fine until it's time to replace the unit.

Kill power to unit. Lower door. Hold down door and remove inner plastic door cover torx screws, rotate up and use inner door cover to brace outer spring loaded door from closing. lift off metal strap that runs along top edge of door. Unsnap black plastic cover.Latch is under cover. Unplug wires with pliers (they just pull off) after noting where they go. Unscrew single hex head screw and remove latch assembly. inside latch will be reused with the new latch switch holder. Pry up plastic clip keepers and remove inside latch. Depending on age they might break, no big deal you will use the new holder anyway. orient and install switches into holder, install inner latch and install assembly back onto door. Install wires, cover, metal strip and inner door in reverse order. Very easy to do. Parts worked perfect.

I removed the gasket from around the dishwasher. Cleans the grove of any dirt, mold or other debris. I started the gasket replacement at the top center of dishwasher by folding the gasket in half to find the center and inserting that center point into the grove just below the latch.i then inserted the rest of gasket with my thumb into the remaking grove first to the right corner then to the left. No told were needed leak was gone

USED A STAR SCREWDRIVER TO REMOVE THE LOWER SCREEN THEN REMOVED THE SUPPORT NUT BY HAND REPLACED THE LOWER SPRAY ARM & SCREEN WORK BETTER THAN EVER.THE ONLY NEGATIVE WAS THE PART TOOK 10 DAYS TO ARRIVE .

Removed 2 each screws from counter top. Pulled washer out 1'. Installed springs and linkage by hand with door closed. Push washer back reinstalled 2 screws.

Used your web site was able to identify correct part very quickly. Received the replacement part in 2 days.
Removed broken part with screw gun only took 20 minutes. Was very please with ease of site and quick delivery.
Thank you