DSF26DHWW General Electric Refrigerator - Instructions

remove the front plate. use screwdriver to pry the cover off from the bottom of the cover, remove the wiring from the front cover.remove the 4 screws and pull out the shute. remove three screws from the solonide and replace . very easy fix. save yourself $100.00 labor.

Cut out cracked tubing between valve and where tubing enters into refrigerator. Cut new tubing to length and attach to existing using union.

ordered replacement part with the understanding that tubing to the water valve could be easily removed. The tubes were carefully removed with some difficulty, and when the new tubes were inserted one leaked. The tube seat was not snug. Therefore a new water valve was purchased. The installation was successful within about 20 minutes. If I were to do the job again, both the water resevoir and valve would be ordered together.

Removed the lower 2 drawers, lower front grill, rear lower compressor cover. Removed the 2 water lines from the quick connects and screws from the water tank. Pulled lines through the hole in the right rear of the refrigerator and removed tank. Then reversed steps to install new tank. The upper plastic tank cover has 2 buttons on top that are really screws with a plastic cap, these are easily removed with pliers.

I followed the instructions on your website. I pulled out the old drive cup and installed the new one. To my regret, I must have broken something in the main ice dispenser during the installation since it would not work. I then ordered a new bin with everything already assembled. I should have done this from the start. Now everthing works just fine.

We just bought a new home and found that one of the clear shelf inserts in a door shelf was pretty much trashed. I was very pleased to be able to find this part at this site . Instead of having to replace the entire shelf I could just put in this part. My only comment is that this clear part is rather difficult to get into the white plastic shelf. I was afraid I was going to break it. But it has to fit snugly. The final result is very nice. Just be aware that these clear shelf inserts do not go in easily.

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

I watched the video provided by PartSelect twice, then proceeded with the removal and installation. It took me 40 minutes from start to finish. Piece of Cake. Everything works fine now.

Opened package and just snapped in front insert. Took longer to open package than it took to replace broken insert.

I was able to snap the new piece right in

1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.

Called the repair guy, he came and said the heater was ok and changed the thermastat.Well that didnt work and the heater looked real bad.So i got one and changed it. Well that worked for two weeks, next i got the motherboard. I looked into it and they have alot of problems with them.And My water and ice machine quitto, so i got one an put t in. So far its not freezing, its been two weeks. But my water and ice machine still wont lite up or work.I was told not to buy Ge buy a service guy before we got it. But the wife went with her cousin and when they got back that is what she got.

1. Emptied the crisper pan,
2. Removed it from the refrigerator,
3. Flipped it upside down,
4. Removed the old one by pulling it off,
5. Replaced it with the new OEM part. and
6. Reversed the process.

Very easy novice could do

I took out the old bins just as when you take them out to clean them. And then I replaced the bins with the new ones.