DLEX8377WM LG Dryer - Instructions

I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.

Screw driver, headlight lamp.. a lot of cursing lol it wasn’t too bad I just couldn’t get it in at first

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '

Found YouTube video followed it closely and did extensive cleaning. The lint on the felt of the drum was causing a rough rotation as well.

Practically got inside of washer. Had to remove a back screw, and use it in the installation. Lining up the screw hole was murder. Mrs. Patrick did repair and ordered part. Service from parts people got me pictures and the right part. FABULOUS service, LG was abysmal, told me wrong part. Two people at Part Select helped me, and sent pictures of part instantly.FABULOUS LILLIAN!!

Could not fix original part. Ordered new lint screen and place it the dryer. No tools needed.

Quick online ordering, part delivered to my home in 2 days! Yay! No more gross lint filter. The new one is exactly what is needed. Thanks! I would definitely order again with your company.

Easy repair, more time spent de-linting the inside of the machine and the duct system.

I accessed the thermostats by removing the exhaust pipe and a plate where the exhaust can be ported on the side as an alternative. You need to get two hands inside to work. I struggled a bit before I noticed the removable access plate on theside. Took about 40 mins to get all three thermostats replaced. not too bad, but it is a tight working space.

Not knowing whether it was the pulley, tensioner, or drum roller I had previously pulled the dryer apart and noticed one roller shaft was rusty for some reason. When the part came in (which was quite fast)I disassembled the dryer to the point that I could remove the left rear drum roller. Replaced the roller and reassembled the dryer (to my surprise without any extra screws or parts left). Fairly easy job, just time consuming.

I first took the top off, then the front control panel, unplugged the wires from panel (very easy), took the front panel off, the rum comes out very easy, be sure to look at the way the belt goes back on the pulley. I didn't and it took me a while to figure it out. All goes back together very easy.

removed the top of the dryer first by removing screws in the back and pulling the top back and up. Removed the control panel, followed by the door. The front panel and top brace were then removed. The belt was disengaged by pulling the tensioner idler and working the belt off the motor pulley. The drum was lifted out and set aside with the other parts. Holding the motor shaft with vice-grip pliers, and turning the nut on the blower wheel (left-hand thread!)removed the blower wheel. The motor is held by snap-on retainers and easily removed and swapped. Installation is reverse of disassembly. While in there, cleaned out the lint gathered everywhere. Also constructed a heat shield out of aluminum flashing and foil tape to cover the foil and foam tape between the burner assembly and sheet metal side. The foam had actually burned at some point in the past and the flashing should act as a better heat shield. A relatively easy repair, but should not have been necessary in a 7 year old dryer.

Unplugged the dryer from the wall. Removed the back bracket holding the top on. Then the top will slide back and lift off. Next I removed the screws holding the control panel. Removed the door. Removed all the screws holding the front cover on. Removed the lent shoot. Manually rotated the tumbler. Checked both rollers in the front. Found one with the flat spot in it. Removed and replaced it.

First the delivery time was incredible, I ordered the part at 2pm on Mnday and recieved the drum Tuesday afternoon. I'm not sure how this was accomplished as I can't even mail a letter across town and receive the next day. Reoved front of dryer removed old drum and slid in new drum. only difficulty was the wiring disconnect on the control board, didn't want to come off. took 5 minutes to work loose.