Models > DLE7177WM > Instructions

DLE7177WM (ABWEEUS) LG Dryer - Instructions

All Instructions for the DLE7177WM
16 - 30 of 63
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Added air diverter on exhaust hose and blew out heat limiter fuse.
Entered dryer from rear exhaust port. Removed 2 screws and 2 clip on wires. A little awkward of process but superior method over disassembly of drum and main parts.
Parts Used:
Thermal Fuse
  • Robert from Jenkintown, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer quit spinning
One of the roller assembly froze up & had a flat spot on it. There for causing the drum not to rotate. Pulled it out replaced the roller & up & running.
Parts Used:
4 PACK ROLLER ASSEMBLY 4 PACK ROLLER ASSEMBLY
  • Peggy from San Bernardino, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace dryer filter
Pull out the worn out dryer filter and replaced it with a new filter that I purchased through Partselect.com.
It fit perfectly.
Parts Used:
Dryer Lint Filter
  • Mike from LINO LAKES, MN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old lint filter was worn out.
I took the old lint filter out and put it in the garbage. I the put the new lint filter in the dryer. Problem solved
Parts Used:
Dryer Lint Filter
  • Dennis from N SALT LAKE, UT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer door latch broken
Part showed up in 2 days and repair took 2 min. Very easy. Thank you!!
Parts Used:
Dryer Locker Assembly
  • Paul from OVERLAND PARK, KS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heater wouldn't get hot - suspected thermal fuse
Removed the top, the control panel and the door. The heater assembly came out thru the front, without having to remove the drum. Easy replacement
Parts Used:
Thermal Fuse
  • Mark from Mendham, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not heat
Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.
Parts Used:
Dryer Thermistor
  • Sal from MORENO VALLEY, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
HST code given by dryer
Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
Parts Used:
Moisture Sensor
  • marty from NEOSHO, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Locker assembly broke
Just unscrewed the original lock and screwed the new one on it was very easy
Parts Used:
Dryer Locker Assembly
  • temeaco from TULSA, OK
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I would turn on the dryer it would run for about 10-20 seconds and then shutoff, and could smell something burning
There’s all sorts of videos on it I watched. It was actually very simple
Parts Used:
Drive Motor
  • Kevin from MASHPEE, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable)
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lamp cover broke
Unscrew the screw, remove old part, place in new part, replace screw and you are done.
Parts Used:
Lamp Cover
  • Lorraine from SEQUIM, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thumping noise when on
watched the video on line then did the repair, very easy to replace
Parts Used:
TUB ASSEMBLY,DRUM
  • Bob from Holiday, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old filter seal torn
Pull filter out and replaced with new one.
Parts Used:
Dryer Lint Filter
  • Frederic from KILLEEN, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer was making a terrible sound.
An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.
Parts Used:
4 PACK ROLLER ASSEMBLY
  • NANCY from ATASCADERO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud rumbling noise
Followed video provided on site
Parts Used:
4 PACK ROLLER ASSEMBLY
  • Michael from RIVERSIDE, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DLE7177WM
16 - 30 of 63
Back to Top