DGHX2655TF5 Frigidaire Refrigerator - Instructions

I took the old cracked door shelf and slid the new one in.

installed end piece onto the glass and placed it in the freezer at the known shelf location

Original unit had screw on lugs. After removing old unit, I unscrewed the lugs, cut the lines to remove the nuts and inserted them into the new unit. Everything was color coded so connection was simple. Reinstalled unit, cycled the ice maker several times only to discover the fill tube at in the freezer had frozen ice blocking the tray from getting water. Used a hair dryer to thaw out the tube, water flowed instantly. Very easy repair.

I TOOK A PICTURE OF THE LABEL INSIDE THE DIVICE SO I DID NOT NEED OT REMEMBER IT WHILE GOING TO MY COMPUTER TO LOOK UP THE PART. I FOUND PARTSELECT AND ORDERED THE PART. I GOT GOOD EMAIL COMUNICATION FROM PARTSELECT ABOUT THE ORDER AND EXPECTED DELIVERY. I DONOT REMEMBER IF THEY KEPT THEIR WORD BUT THE PART CAME IN SOON ENOUGH. WHEN IT ARIVED I GOT MY BOX KNIFE AND CUT THE BOX OPEN TOOK OUT THE DRAWER AND SLIDE IT INTO THE SPOT WERE THE BROKEN DRAWER WAS. I DID CLEAN THE SPACE WHERE THE OLD DRAWER WAS IT WAS EMBARRISING DIRTY. I WOULD RATHER NOT TALK ABOUT THAT BUT IF YOU LIKE I CAN SEND PICTURES. THE DOOR IS WORKING FINE JUST LIKE THE ORIGINAL ONE DID. PARTSELECT WAS A GREAT CHOICE IT WAS QUICK AND EASY. IF YOU DONT USE PARTSELECT YOU ARE GOING TO JUST MAKE YOUR REPAIR HARD ON YOURSELF.

My repair plan is to continue buying parts for it until is starts working. I notices a large rusty stain on the back of the refrigerator, so I replaced the Ice Maker. Then, I replaced the Evaporator Motor. Yet nothing will come on.
I called Conn's Home Plus where I bought the Frigidaire Refigerator back in February 2014. The Tech said that It needs a Board-main Power (computer part). So I it ordered from PartSelect. It is due here by July 20, 2020. The Parts and Tech cost is now over Five Hundred ($500) dollars.
HELP!! I need INSTRUCTIONS, HELP!!!
Albert F. Alfaro in San Antonio, TX.

Consulted You Tube. Took off old gasket. Easy. Put on new one after getting it warm. The track on the new gasket did not sit properly. Took multiple attempts but finally worked. Size was perfect but the gasket color was different than original and therefore, different from the refrigerator door. No tools required.

We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.

I took out the broken drawer and replaced it with the new drawer

Slid right in.

As it turns out when i pulled the drawer out and then the door holder i discovered that there was a big piece of material that was suppose to be around the water line that was causing the problem. The old drawer holder was not the problem so the new piece was not needed. All is well.

I ordered the replacement part, and when it arrived, I used a flat-blade screwdriver to remove the two glides from the old drawer and installed them on the new drawer by snapping them into place. Then I removed the sliding humidity control from the old drawer using gentle pressure, and installed it on the new drawer. Then I slipped the drawer into its place, loaded the vegetables into it, and was done in less than 5 minutes.

Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike

Very easy

slide old filter out and insert new one

I looked at the internet before I purchased a new seal and saw how to repair it. It was a matter of pulling out the old seal and just popping in the new. The internet said to use a hair dryer to melt the rubber to adhere to the fridge in places where it wasn't. It was quick!