DE170ADW1 Westinghouse Dryer - Instructions

when the bearing broke the drum fell in the back. I tore the dryer apart, ordered the part and fixed it when the part came. the dryer runs like new now!

After figuring out how to remove the top, front, and control panel from the Gallery series, which is different than the dryer in the video, the repair was easy. Just followed the rest of the proceedure in the video.

I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.

Had the macnine apart before ordering the Bearing Assembly. Reading other comments convinced me to order the Bearing Assembly. Parts were shipped very quickly after ordering and following the instructions on the web site things went back together easily.

The consensus seemed to be that the loud squealing was most likely the rear drum bearing needing to be replaced. Although the repair went very well (great video!), it did not fix the problem. BEFORE you go the route of replacing the rear bearing, first pop up the top and see if a little piece of plastic that is attached to the top middle of the front panel by a screw is rubbing against the drum (you have to have a load going). I removed this part (I could not find it listed on any parts list) and the squealing stopped. I have no idea what the purpose of this part is, except for maybe keeping the drum from dropping too far down if the load is really unbalanced. This plastic part is on the dryer that has the controls on the front (it has the ability to be stackable) and might not be on the other unit that has the controls on the top back. If anyone has posted this as a possible cause of the squealing, I haven't seen it.

First I like fixing things for myself. So I looked the problem up on the internet. Found the repair tech that I needed. The found your parts site. And BOOM. Looked up mt part on your site. Very easy you had everything I needed. And you got it to me quick. THANKS. When the part hit my mailbox. Everything I needed was there. I pulled the plug. Fliped the lid up. Took off the front. Removed belt off the ideler. Removed drum replaced bearing assy. Put it back together. Closed the lid and pluged the unit in. Worked so well I felt like a pro. My wife was tickled pink. Just like a new one. Thanks guys for making me look good and saving me a lot of money. Will use this site again. I give you 2 thumbs up.

Repair went just according to the video except to pull the drum out there was a plastic lock at the front of the dryer. It was held in by one screw and easy to take off. When I pulled the drum out the armature and spring that hold the belt tight fell off. I panicked a little, but easily put the pieces back in place. When I started the dryer for the first time it sounded odd but realized it was the sound of all the grease spreading itself around the bearing.

Found instructions on "UTube"some of the screws were in a different position but you can see them. While you have the dryer apart it's a great time to clean it and also as long as you've gone this far replace the belt,it's probably time.

This is a front load dryer. First unbolt top cover of dryer. Then unbolt screws and connections to control panel. Next unbolt all screws holding dryer door and front bottom panel. Next take belt off of drum and slide out drum from the front. From inside of drum remove 3 screws and remove bearing then put new bearing on and bolt up the same way you take old one off. Using an 8mm socket or wrench remove plastic bearing cage located at rear of dryer. When unbolting there is a retaining clip and small steel ball to be removed from back of dryer. Replace this the same way you take it off. He sure to grease the bearing cage then replace everything back from putting the drum in first to your last step bolting on top cover of dryer. Hope this helps anyone doing this repair.

Hired a professional!

I highly recommend watching the repair video. I could stop the instructions and do the procedure then resume instructions for the next step. I would recommend you have a second person to help lift the drum up & out of the dryer frame. And ladies please instruct your husbands to watch the video all the way through. Mine lifted the top off the dryer and stuck his hand in and cut his finger immediately on a sharp piece of metal. You know because they don't need to read the instructions.

Unplug dryer, remove rear access cover and removed belt from pulley. Remove bottom cover on front of dryer, remove top of dryer, unplug harness to control panel and remove front door assembly. Remove screws from drum to bearing assembly. Removed drum and belt removed bearing assembly by lifting up and out of the bearing socket. Vacuumed all the lint. Removed the bearing socket, installed all parts and covers in reverse order.

I followed instructions I found on u-tube to remove the drum and belt and access the bad bearing and change it. The instructions were quite good other than needing to remove a small panel on the back of the dryer to pull the belt around the tensioner.

Followed the video, it was good, the instructor's tips were useful and time saving.

Followed video that was provided!! Now I know how to get the top and front of dryer OPEN. Now I can clean interior of dryer ALSO, lots of lent!!