All Installation Instructions for General Electric Dryer DCCB330ED0WC

Dryer was not heating at any level and it was making noise while rotating

First, I unplugged the dryer, pulled it out into an open area. I then removed the vent hose. I opened the front door and removed the 2 screws that hold the top panel down. Once removed, I lifted off the top which exposed the drum. Next, I remove the 2 screws along each side that allows the front door panel to detached. I noticed that there was damage to the plastic bearing and 3 bearing pads were missing. That was the source of the noise. Once the door panel is lifted off the cabinet, the wires to the safety switch must be pulled off so the door can be set aside out of the way. Then I went to the rear and remove 2 more screws that gave access to the motor, wiring and the tensioner for the dryer belt. Once I gained access to the belt, I slipped it off the tensioner and drive pulley. This allows the drum to be removed from the cabinet. WE wrestled the drum out before realizing that we should have removed another 2 screws securing the sides of the dryer to a cross support under the front of the drum. This would have made the removal of the drum much easier. Once the drum was removed, I had access to the heating coils. Upon examining, I saw that both had burned out at the far left terminals. Directions that came with the new heating elements gave clear instructions on how to install. It's a little daunting to thread both elements through all the insulators, but patience paid off. Everything went back together easily and the dryer started up and heated up just like new.

Parts Used:

Front Drum Bearing

Robert from Louisville, KY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broken piece

Snap out the broken part. Snap in the new part. Use caution with the wires, but don’t have to disconnect them.

Parts Used:

Dryer Lint Chute Assembly

Kevin from GALES FERRY, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Purchased a used dryer & lint filter had holes due to rust

On my GE Dryer the lint filter is located inside the door at the bottom. The filter can just be pulled out by hand & a new one pushed into place

Parts Used:

Lint Filter - White Frame

Barry from WARRIOR, AL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

old screen was not sealing properly

Replaced new screen in place of old one.

Parts Used:

Lint Filter - White Frame

Thomas from Wake Forest, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

door filter

was no repair- removed filter from door and installed new filter into door. No tools required.

Parts Used:

Lint Filter - White Frame

victor from ST AUGUSTINE, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

take the old dryer lint screen out

Hand replace

Parts Used:

Lint Filter - White Frame

Dave from EDGEWATER, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

My last phase of repairs of minor items.

if your unit has over 6,000 hours of operations, one needs to remove the front panel and inspect the sliders that the drum rides on. The video were very helpful to replace the sliders. Unfortunately, my dryer had over 10,000 hours of operations over a 30 years period, hence a major repair costing over $200.00 dollars. The drum sliders were gone, hence the drum eat through the plastic guides. More so, the drum started to eat away the front panel. If the dryer is eating your closes and making a noise, one is looking at a $200.00 repair job. Hence check the sliders early will save one $$$$.

Parts Used:

Dryer Lint Chute Assembly

Edward from EDGEWATER, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Switch not working.

Open the door and removed the part. Installed the new part and started the dryer.

Parts Used:

Door Switch

Alan from BELFORD, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

inherited machine, lint filter missing

Searched the sites order # online, called, ordered, delivered PDQ, unpackaged, popped in. That was it.

Parts Used:

Lint Filter - White Frame

KAREN from THIBODAUX, LA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

My lint filter had a big hole in it. My dryer is 10+ years old.

All I had to do was remove the damaged filter and replace it with te new one. It could not ave been easier.

Parts Used:

Lint Filter - White Frame

JUDITH from FRUITA, CO
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Plastic tab broke on handle --- temp taped on.

My daughter, who has the dryer in Florida, made the repair herself. She removed the broken handle that had been temporarily taped in place. Cleaned off tape residue with Goo-Gone. Then took the new handle and snapped it into place. Worked just like it was supposed to.

Parts Used: