DBSR463GG4WW General Electric Dryer - Instructions

Pulled off old knob and snapped new one into place. Took about 5 seconds. Must be a lame design cause my dryer's less than 2 years old and the knob snapped on the inside and wouldn't turn. Easy to fix though.

Dryer is 3 yeras old. This dryer switch / start knob broke three times. First two GE repair fixed it. Charge was about $75 to $100. Then I found Parts Select, Who what great prices. Switch cost under $10. and took me 10 minutes to install. Dryer works great again. OH, I ordered an extra switch to have on hand.

I am a 55 year old woman who likes to repair household items. I followed You Tube instructions and did it all by myself. A few screws to get the top off and a two more to remove the front piece. Trap duct assembly was cracked and falling apart. Pulling off the old was fairly easy. I watched the You Tube instructions on my Ipad so I could rewind and watch as I did it. The hardest part was I dropped one of the screws when placing the front of the dryer back on and had to find another one that was the same size. Luckily I have lots of old screws in my tool box, If you like to do small simple repairs to save some money this is an easy one.

-- Unplug dryer from electrical outlet
-- Open Door
-- Remove two screws going up into the top panel
-- Remove top panel
-- Close door
-- Remove two screws holding front panel
-- Remove Front Panel by turning out, keeping left side close to unit since wires are still connected.
-- Vacuum out all loose dust/lint
-- Tilt old Drum bearing toward you to remove.
-- Remove Old Felt Drum Seal
-- Install drum Slides on new Drum Bearing
-- Install new Drum Bearing, make sure it clicks into place securely.
-- Install new Felt Seal, make sure to push in far enough to securely hook to the clips on the bottom of the Drum Bearing.
-- Reinstall front and top panels
-- Plug in electrical
-- Dry

I was using vice grips to turn the control knob (stub) until the new knob arrived. The replacement knob was a redesigned type with a metal backing plate to place on the control knob stub (better than the original plastic knob) however the diameter of the new knob is only half the size of the original knob and the mark on the dial does not line up with the markings on the dryer control panel making it difficult to know what cycle you are using or how far to turn the dial within each cycle before passing to the next cycle.

Just took out of plastic wrapping and put on dryer. No tools needed.

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

Follow YouTube "how to change dryer's belt" some video is very clear.

Easy repair, but did take a little longer than anticipated due to the extra cleaning that I did while the dryer was disassembled (highly recommend). First, unplug the power cord. Then, open the door, and locate the two screws in the upper corners, and remove. This will allow you to remove the top cover. Be careful and work the top panel up and down to loosen the control panel tabs, and set aside top panel. Next, remove the two screws located near the top on the inside of the front panel. Removing these two screws will allow you to lean the front panel forward, lift up, releasing the tabs holding the bottom of the panel. Be careful when you pull the front panel from the dryer as you will need to lift the drum off of the front bearing which is attached to the front panel as it is removed. You will also need to use your needle nose pliers to remove the wires prior to setting the panel aside. The wires are straight forward and power the light at the top, and the safety door switch. I always take a picture with my phone's camera just to validate when I re-connect them. Reaching underneath the drum you will be able to feel the belt and belt tensioner pulley. With both hands under the drum, use one hand to push the pulley to the right, releasing tension on the belt. Move the belt out of the groove, and let it hang freely. Now from the top of the drum, bump the drum to loosen, and remove from the cabinet. It is a tight fit, so you will need to spread the sides slightly in order to remove the drum. Next, remove the 3 screws holding the heat diffuser in the rear of the drum in order to remove the rear drum bearing. (Tip: It would be nice to have a helper hold the new drum bearing in place when starting the screws, and it also helped to tighten each a little at a time to keep the new bearing flat as it was drawn up next to the drum.) Tighten the screws holding the new bearing in place. Next, remove the 4 small screws holding the heating element housing to the rear of the dryer. (Tip: Rather than disconnecting the wires, I used a bent coat hanger to hold the housing while I removed the bearing retainer and clip from the rear of the housing.) Remove the 4 screws holding the bearing retainer and clip, and replace with you new part, paying close attention to the clip's position, and tighten. Replace the housing to the rear of the dryer. (Tip: Now is a good time to familiarize yourself with the belt and tensioner pulley for reassembly. Also, it may be a good idea to look at your belt, and replace as needed.) Next, reinstall the drum and insert the new bearing shaft into the new bearing housing. Using both hands again, reach underneath the drum, locate the tensioner pulley, and belt. Push the tensioner pulley over to the right, and move belt over the pulley on the motor, and behind the tensioner pulley. The belt should be tight. If not, inspect to ensure that the belt is over the motor pulley, and the tensioner pulley. Next step is to reinstall the front panel. I also spent the extra money and replaced the front drum bearing, and slides. Please note that the green slides are on top, and the white slides are on the bottom. Lift the panel over the tabs, lean forward while lifting the tub, resting the tub on the front bearing. Reinstall two screws in the upper corners, and tighten the front panel back in place. Now is a good time to turn the drum to ensure that the belt is in place, and that the drum turns correctly. (Tip: If your dryer is equipped with a light, you may also want to replace the bulb in the front panel (if needed) prior to attaching the front panel.) Reinstall the top panel by aligning the tabs in the control panel with the top panel, being careful not to bend the tabs. Next, open the front door and use the 2 long screws to reattach the top panel to the front panel. Plug in power cord.

Replaced High limit thermostat per video on the website. However, the flange of new thermostat is flat, while chassis it mounts on is round to conform to drum of dryer. So new thermostat was not flush with chassis. Dryer did not shut off early (that problem solved), but instead continued to dry clothes beyond time necessary. Note that old thermostat had one side of flange slightly bent and probably more flush with chassis, and better able to sense when hot temperatures were reached. I dismantled dryer again, slightly bent new flange, re-installed. Seems to work better now .

Son found out where the bulb was by using YouTube. I googled lamp for model number and your website came up. I ordered the part, it arrived promptly, and my son installed it.

I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.

remove the broken one and replace it with the new one

I watched the repair video 3 times to make sure I was comfortable to do the repair.the video was very helpful.thank you ! Everything went well and the dryer runs great.