All Installation Instructions for General Electric Dryer DBLR333GG8WW

not drying clothes, felt seal hanging in the dryer

Took dryer apart replaced felt seal and the four drum slides put it back together works better now than when it was new!!!!!!

Parts Used:

Duct Felt Seal

DRYER BEARING SLIDE GREEN 2PK

DRYER FRONT BEARING WHITE 2PK

Adrian from Rutland, VT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

belt broke on dryer

good replacement procedure on you tube.

Parts Used:

Drive Belt

rodney from VANCEBORO, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dryer Not Starting

First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine

Parts Used:

Drive Belt

Scott from Poughkeepsie, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

evidently the pulley spring on video was very very very weak

the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.

Parts Used:

Drive Belt

tim from NEW PRT RCHY, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broken control knob

Pulled off the broken control knob (which was really easy, since it was already broken.) Aligned the new knob to the knob shaft which is shaped like a "D", pushed it onto shaft until it was fully seated. Very easy install!!GT

Parts Used:

Control Knob and Clip - White

Kim from SPARTA, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The dryer lint chute was cracked and catching our clothes.

We watched the YouTube video and had it installed in no time. Saved money doing it ourselves.

Parts Used:

Dryer Lint Chute Assembly

Renee from Leesburg, VA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

knobs cracked

Push on. But one pushed in panel

Parts Used:

Control Knob and Clip - White

Dorothy from LACYGNE, KS
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer needed a new dryer belt

I followed the directions I found on my tablet on youtube.

Parts Used:

Drive Belt

Cindy from EPHRATA, PA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

loud noise when ran for 5 min.

Replaced the rear drum bearing. Not doing it before ,it took about 1 1/2 hrs. Problem was fixed.

Parts Used:

Rear Drum Bearing Kit

Joseph from Freeland, MI
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Drum would not turn

Exactly how your perfect video instructions showed me. Thank you for a job well done!

Parts Used:

Drive Belt

Jeff D from NEW MEADOWS, ID
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The dryer would not turn on.

We took the knob off of the machine and it appeared to be cracked on the inside. We ordered a new one and received it in 2 days. We matched the inside of the new knob to the stem coming out of the machine and placed the knob on the stem. The machine was fixed and we were happy! Thanks Part Select.

Parts Used:

Control Knob and Clip - White

Anna from LELAND, NC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Knob broke because Timer stopped working

Ordered & received new Timer & Knob. Disconnected dryer from power.
Located screws on back of dryer console & removed screws so console could be tilted forward.Used cell phone to take picture of timer with connections to keep track of where to reconnect wires. Unsnapped connections to timer. Removed old timer and attached new timer. Attached new knob to front of console. Plugged dryer back up to power and tested by turning new knob. Reattached console with screws. Done!

Parts Used: