All Installation Instructions for Dryer DBB3300GA2AA

Timer knob had cracked and would no longer turn. The lint filter had a whole in bottom

Just took out of plastic wrapping and put on dryer. No tools needed.

Parts Used:

Lint Filter - White Frame

Timer Knob

Robbi from UNION, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Too much drying time, not hot enough

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.

Parts Used:

M Series New Style Coil Kit

John from Floyd, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

My drier would start create heat,than stop heating after 8-10minutes.

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

Parts Used:

M Series New Style Coil Kit

Tom from Schaumburg, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Dryer heat would go off and timer would not move. Dryer would continuously run

Replaced coils on gas valve.

Parts Used:

M Series New Style Coil Kit

chuck from smithtown, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Catching clothing and reping

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

Parts Used:

Dryer Lint Chute Assembly

Jose from LILBURN, GA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

the felt in front door worn out

i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat

Parts Used:

Duct Felt Seal

gerard from goldsboro, NC
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

5 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Dryer's drum doesn't run

Follow YouTube "how to change dryer's belt" some video is very clear.

Parts Used:

Drive Belt

ruoli from Germantown, MD
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

GE front load gas Dryer not lighting after it initially starts

I removed the right side panel and top panel from the dryer. I removed the 2 wire and 3 wire connectors from the 2 coils. I removed the bracket holding the 2 coils, replaced the 2 coils, and replaced the bracket. I reconnected the wires to the appropriate coils and replaced the side and tops panels on the dryer. The dryer now lights every time the dryer calls for heat.

Parts Used:

M - Series Secondary Coil - 2 Terminals

M-Series Primary Dual Coil Gas Valve

Bruce from CLEVELAND, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dryer was shutting off too early, before clothes could dry

Replaced High limit thermostat per video on the website. However, the flange of new thermostat is flat, while chassis it mounts on is round to conform to drum of dryer. So new thermostat was not flush with chassis. Dryer did not shut off early (that problem solved), but instead continued to dry clothes beyond time necessary. Note that old thermostat had one side of flange slightly bent and probably more flush with chassis, and better able to sense when hot temperatures were reached. I dismantled dryer again, slightly bent new flange, re-installed. Seems to work better now .

Parts Used:

High Limit Thermostat - L290-40F

Anthony from LAWRENCE, MA
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Gas Dryer Runs With Heat for Less Than 5 minutes, Timer Won't Advance in Autodry

My gas dryer would run with heat for 5 minutes in all settings, but kick off and not heat again. Timer would not advance in autodry. Thought it was the cycling thermostat, so replaced that, but did not solve the issue. Ordered the coils, and cleaned out heavily clogged lint from bottom of lint trap, especially right above the fan motor at the bottom of the trap. Received the coils, opened the top and front, took out drum, and replaced the coils. The replacement took less than 2 minutes. Be careful putting the drum back on to make sure the felt is not caught inside the drum. You can give it a spin to make sure. Wear gloves, as I cut myself up pretty good on the edges of the dryer body. The inside of my dryer looks like a crime scene! Anyway, I put it back together, and it runs great. Solved the timer advance issue in autodry, and the heat kicks on and off when it is supposed to. Good luck! Thanks Part Select!

Parts Used:

M Series New Style Coil Kit

julia from WOODRIDGE, IL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

ignitor failed to ignite gas or would fail to after first ignition.

Watched youtube video to problem shoot. Cause determined to be coils bad. Searched web found Parts Select to be easiest site to deal with and had coils for best price. Followed instructions supplied with parts. Dryer works like new.

Parts Used:

M Series New Style Coil Kit

CHUCK from HARDIN, KY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

handle fell off

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.

Parts Used: