CYE23TSDASS General Electric Refrigerator - Instructions

Watch this very good refrigerator evaporator fan replacement video

Repair man thought it was the control board and an issue with a relay on the board. Purchased the new board but found out the board was fine, and it was the recirculating fan that would go out intermediately.

Tried ordering that part from Part Select since they have been great, but GE discontinued the part and their was not a replacement available. After much research, found the new replacement part number and ordered that, it went in quickly and for now seems to have solved the problem.

Took the drawers out of fridge and unscrewed the support rails for drawers and unscrewed inside back wall of fridge. Removed cover on blower fan ~ unplugged fan. This took 45 mins. Left refrigerator unplugged and let thaw out. Replaced with new fan 5 days later. Plugged in new fan. Then
Plugged in refrigerator to make sure it would work. After 15 minutes, unplugged fridge and put rails and drawers back. Total time 45 minutes. Plugged refrigerator back in and let run 24 hours.
It took 5 days to get part due to snow storm delaying delivery. It works perfectly. Our GE will be 10 years old in August.

GE sent a technician to our home. He listened to the video I had made of the loud noise the fridge was making and he knew what I needed without even looking at the appliance. The parts would take 60 to 90 days due to distribution chain issues. He gave me the part numbers and I paid him $140.00 for his service fee.
I found the parts myself that I needed on PartsSelect.com which arrived with 2 weeks. I watched a YouTube video on how to install the parts. The hardest part was emptying my entire refrigerator of perishables so I could easily get to the malfunctioning fan motor and the motor’s boot. I used a heat gun to dislodge ice clinging to the parts I needed to remove to reach the fan motor. It worked well. Once I was able to detach the old fan motor & its boot, I easily slid the new one into its place. I then reattached everything I had disassembled. It works beautifully without disruptive noise.
The water filter cartridge door also easily snapped into place, replacing one with a broke latch.
I love the saying,
“What one man can, another man can do.”(Except I’m a girl - my husband was amused).

Removed the bad inlet valve and installed the replacement. Very easily done. The replacement part made the repair so simple and saved me a huge amount over calling a repair man. It did not take any special knowledge.

Received replacement part. There is a cover over the ice box latch. Pried it off with a screwdriver head. Took the broken latch off replaced new latch to cover and replaced on the door.

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

EXCHANGED THE LED LAMP ASSEMBLY. ONLY DO ONE AT A TIME AS THEY ARE WIRED IN SERIES!

followed install on line

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

I ordered the correct part, the box said it was the correct part and when I opened the box a completely different part was inside. Not only was it the wrong part but it was loosely wrapped with very thin plastic and the hinge was broken off of the lid and laying in the box. I have called and emailed for help and was told no one was available to help because of COVID 19. One email was answered to return the part I would have to pay shipping and the part could not be damaged. Okay, the part was wrong, the part was broken. Now what should I do? Please respond.

The glass fits easily under a plastic ridge that is the frame holding the 2 vegetable drawers below. Slide the back side of the glass under the ridge, and then gently place the front of the glass in the groove where it goes on top of the vegetable drawers.
Its Super simple, and takes literally 30 seconds to complete.