CWG3600AAS Maytag Wall Oven - Instructions

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wire pull the old igniter out.
Install new igniter, by mounting to frame with two screws, feed the two wire assembly through the hole
behind the gas tube, reconnected the wires, oven started right up. PartSelect was great, received the part very fast and there feedback comments are a big help.

Make sure the knobs are all in the off position before starting the work. You may feel more comfortable shutting the gas valve off behind the stove or in the basement first, just make sure you fire the burner and let the gas that is left in the line burn off.
Remove bottom pan in oven by sliding the pins (located in the back) towards you and picking up the back of the pan and pull it away from you, this will slide the pan off of the other 2 pins that you can not see on your end of the pan. Take the flare shield off from over top of the gas line (should be 2 nuts or 1 wing nut). Remove the screw or screws that hold the heat shield covering the ignitor wires and remove the heat shield. Unplug the ignitor. remove the screws holding the ignitor and remove it. Be sure to order the ignitor with the extra shield and make sure it has new screws, you may need to replace the screws. Try not to touch the element of the ignitor. it can be very brittle. It seems lengthy but is very quick and simple.

removed 2 screws on element then unpluged it then replaced it with new one easy job

Remove oven floor and bottom drawer
remove 2 1/4-inch screws holding ignitor
remove cover plate behind drawer to access P/J
Disconnect plug remove ignitor and reassemble

Did not have gas smell, but ignition took 6 minutes

First I called a local repair shop and after getting a 325.00 repair estimate I looked up your website and discovered that I could purchase the part for 46.00 dollars and followed the do it yourselfers imput Now thats what I call a savings

I opend the bottom cover, which had for screws then , opened 2 screws that atached the igniter to the main gas pipe and pulled the whole wiring out and disconected the wiring , ordered the igniter two days later, I put the whole thing together in less than 5 minutes . put back the cover. and I tried it , everything was cool , accutaly hot and working .

We hired the neighborhood handy man, and he was able to repair the oven in about 15 minutes. I order the part and received it the next day. Excellent Service!!

My stove would take forever to preheat and sometimes it wouldn't heat above 175. I order a new igniter, which was located under the drip pan . It took less then ten mins to replace and the stove is working like new.

very easy

First I tried oven ignitor. Did not cure the problem. Then ordered short sensor and it cured the problem. Pull range out & unplug unit.From inside unit remove two screws holding short sensor in &pull out from inside. Unhook sensor. Slide in new sensor& secure with two screws. Had to remove two screws on back of oven to plug in sensor to existing plug. Very simple job.

Removed the old igniter, followed the wires. Reversed the process and put it back together. Saved big bucks! Thanks for the quick service.

We ordered the replacement igniter and basically was very easy to replace. We ended up spending $50 for the part as opposed to spending $261.00 that Sears was going to charge.

Removed oven bottom were you see the light glowing from then unscrewed igniter unpluged then took it out and put in new one went well i would do it again works great

First I unplugged the range, turned off the gas to the oven and disconnected the gas line from the oven. I pulled the oven out to gain access to the rear of the unit and unplugged the old igniter. Next, I removed the oven door, removed two screws to the floor of the oven and removed it. I then removed the metal covering above the gas component allowing full access to the igniter. I removed two screws from the igniter and removed it. I positioned the new igniter and replaced the two screws. I replaced the covering over the gas component, replaced the oven floor and put the oven door back on. I went to the rear of the unit and plugged in the new igniter. I then reconnected the gas line to the oven range and checked for leaks, No leaks were found and I pushed the oven unit back into place. I pushed the Bake button and the igniter started igniting the oven.

Job completed.