CWEF310GSF Westinghouse Range - Instructions

It was a little difficult by my self an extra hand would of made it much easier.I unscrewed the screws pulled the wires from the back of the oven which took a few minutes.I am not great at fixing things but once I got the old one out it went smoother than I expected.it took about 25-30 minutes with an extra hand could have made it 10 minutes.not bad over all for me.did I mention not very handy.did stun the wife that I fixed it on my own.thanks Bill

Twisted replacement bulb into place easily. Let there be light!

When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!

Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove baking racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!

I unplugged the stove for precautionary reasons.
I then removed the two screws holding element in place with the correct nutdriver.
I then carefully pulled out the element and pulled the two female spade connectors off.
I then compared to new element and plugged the new element in.
Finally I screwed in the new element and tested the oven.
It worked again!! I would recommend running the oven for a bit before placing anything in to bake. this allows burn off of stuff on the new element.

First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.

Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

Ordered new racks and replaced them.

pulled oven out, unplugged, unscrewed element attachment to the back of the oven (from the inside). element did not work. we tested the upper element and that did not work either. the burst of sparks, heat and flame from the shorting of the original element caused damage to the computer board. we called a local repair man to change the computer board, and then the unit worked, with our new element that we replaced!

Pulled out heating elements. Removed old drip bowls. Inserted new drip bowls and re-installed heating elements.

I was extremely pleased with the very quick delivery of needed parts.

First of all I would like to comment on how it easy it was to place this order and I was pleasantly surprised that it was rec'd the next day. Also it was the correct part that I needed. To install it, first I removed the screws and then the metal that was holding the broken glass. Once the broken glass was removed, I set the new glass in the metal strips and basically screwed it back together. Please note to be careful to remember which screws go where as they are not the same size and do not fit anywhere but where they belong. That was the only part of the job that I had a problem with.

The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put the next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will hold it in place.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!