CWE6800ACE Maytag Wall Oven - Instructions

Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Ordered the part from part select, it arrived quickly, and it only took minutes to fix. Could not have been easier!

Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.

very easy

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Took the door apart and replaced the hinge, very easy

Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!

We had a wood tray in the oven (yes i know) and it is a two stacked oven and turned the wrong oven to broil. The fire was put out quickly but the Latch door switch and assembly was damaged.
The 3D breakout of the appliance made it a jiffy to select the correct part numbers. Shipping is very good from Parts Select.
The Front assembly for the lower oven comes out with 6 screws. Disconnect the Door Switch Connector push it out and replace that. The Latch Assembly requires a small wrench. It is a bad design but patience will get you there. Once the assembly is out disconnect electrical connectors. Don't worry each connector is unique I advice do it one for one.
Overall you need a skill of three stars out of five to complete this task

Pulled oven door out of oven and and replaced glass.

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!

Watching the video of how to replace the sensor was great help and much appreciated, the only difference was that my wires were much shorter and I had to pull the oven out of the cabinet to get to the back of the oven to release the clip holding the wires together, unlike the video where the man jiggled the wires until the clip holding the wires together came through the little slot where the probe is attached, otherwise it was pretty simple, just a few extra steps to pull the oven forward to get to the rear to release the clip holding the wires together. Once I was able to release the clip I used one of the 2 adapters that was sent with the sensor probe and attached them after putting the wires through the hole where the probe was attached first then replaced the 2 screws that holds the sensor in place, slid the oven back in and turned the circuit breaker back on and it works perfectly. The video gave me the confidence to do this job though and I thank PartSelect very much for being a great company to help with videos and sending the parts so quickly.

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call