CVM9179SL1SS General Electric Range - Instructions

I replaced the switch at the bottom per instruction. I had both switches. I think it was the monitor door switch.It works fine now. Thank you Part Select .

Replace the burned-out bulb with the new purchased bulb

Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...

Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.

I replaced old tray with new. Received replacement part in two days. I was surprised at the quick response time. The part ordered was right the first time.

I purchased the fuse and 3 door switches from PartSelect. Replaced the fuse first but that did not solve the problem. Then I replaced the 3 door switches and problem solved!! So fuse only cost $5.00 so glad I have a new fuse in there as well. To see how to replace door switches see videos on utube!!

While cooking squash for 20 min the microwave quit. No lights, nothing. Initially, I looked at fuses and tested thermostats whille leaving the unit in place over oven and removing control panel. One thermostat one base under fan showed no continuity so I replaced it just to find it was normally open so the problem remained, no power. After looking at schematic I saw the negation thermostat on the top of the megatron which would require removing the unit from the wall and disabling the unit cover , removing the vent duct. Immediately, I knew that had to be the problem since there was nothing more difficult to reach. Sure enough, after disassembling the unit, removing everything removable, I tested it and it was dead! No continuity! After replacing, everything works fine. Other than being a pain in the *** , it was pretty easy. Just a ton of screws to remove everything very obvious. The frustration is that there are two fuses, and two other thermostats right up front that would have been easy to replace but nooo. Can’t be those :-).

Unscrewed numerous screws holding the "body/shell" to the microwave. Removed body. I then unplugged top door switch, replaced it with new one, and "tested" the new one. I fixed our $400 convection micro with an $18 switch. NICE!

It took less then 10 minutes to order. Received new part with 3 days

I took the cover off, and replaced the glass-- the difficult part, was ordering the glass..on the list of parts to order-- the description of the glass was mis-leading

First I replaced the cracked cooking tray and I was done.

Followed the online videos to enter the cavity to the switch holder. Noticed right away the dreaded capacitor was in back right corner behind where the touch pad had been removed. I isolated the capacitor with an old computer mouse pad for extra safety. Took some manipulations to get the switch mount out from behind the wire bundles. Once out front, easy to use small flat blade screwdriver to release each switch and replace with matching new switch. Only one switch was bad but replaced all three. Back together and working great.

Two screws to remove upper from vent. Two screws to remove the didgit panel lift ip to remove and put aside remove the two screws that hold the door sensors. Depress the tab to remove the defective sensor disconnect the electrical connector and replace the new sensor snap it back into the holder install the two screws, install the didgital panel and vent panel to complete the job. Please be aware that there is a video of this procedure on Y tube

New one arrived very quickly.

Right part. Right on time. Fit like it should.

Excellent service.

Removed control panel disconnected old capacitor installed new and returned the leads back on to the new. replaced control cover and tested