CVM9179SL1SS General Electric Range - Instructions

I've been fixing and taking things apart since I was a kid. I hoped that it was a bad switch in the door. Got out my test meter and check the 3 different switches. All 3 tested good, but one was a bit hit and miss. It would work if the microwave was on its side and wouldn't when it was set flat. I found the switch online and installed it. Took care of the problem.It was a whole lot cheaper than buying a new microwave. Thanks! Bill Brown, Fridley, MN

Extremely easy. Less then 10 minutes tops.
Remove the screw holding the cover to the lights.
Remove the burned out bulb(s) (they may give a little resistance).
Carefully line up the holes for the prongs on the bulbs.
Insert the prongs firmly but gently using the styrofoam holders the bulb(s) was/were shipped in so as not to touch the bulb(s) with your fingers.
Replace the screw to the light cover.
Turn on the lights and give yourself a pat on the back.

The switches are not the problem! The problem is in the tolerences of the latch housing. I have ordered two new housings (Upper & Lower) and will see if the tolerences are closer. If not I will try epoxying a shim to the plate that operates the microswitches. The other option is to file the mounting slots of the housing to allow adjustment, which would be iffy,keeping them from moving with use. The exploded drawings really need to be clarified. The scale is way too small. It was extremely difficult to pick out the individual parts of the mechanisiam.

All electrical worked (fan, lights, control panel) door switch was broke. Pulled the oven out. Took out two big screws from the cabinet above. (be careful not to drop oven)Set the oven on kitchen counter. Took off five screws that held the vent cover. Removed vent cover. Took out one screw that held the control panel. Lifted, turned and slid the panel into the space below so I could get to the upper door switch. Replace door switch and re-assemble.

Took cover off, noted the two side by side switches easily visible and we hought one of these was responsible. Then son noted a third switch at the top of the plastic assembly which inserts at an odd angle. When it was inspected signs of a previous short showed up with burnt contact points. Reinserted at same odd angle as there were guide holes, closed things up and oven worked 100%. Great prompt service and great website!! We will use you again

Primary door switch was shorted and blew the fuse when the oven was plugged in. Replaced primary door interlock switch.

first i remove the screw, then removed the lens assembly (really a frame) bent the feet out of the way, slid the old lens out and the new one in, bent the feet back in place and inserted the assembly into place replaced screw. the killer is a day later it was broken again, think the lens can't handle the heat from the oven below or the lights above. you guys where great fast and exact match part but the ge design is flawed

Took the screw out of the glass door holder, bent the clips up and removed the broken glass. While this was open chenged the light bulbs as well. Put new glass in bent the holding clips down and closed the doors and installed the screws again. So nice to have good light again and also new glass in them. Never noticed they were broken before.

BY THE WAY PARTS SELECT IS VERY PROMPT AND I RECEIVED MY PARTS IN ONE DAY AFTER THEY SHIPPED. SHIPPED ON MONDAY GOT THEM TUESDAY, thanks parts select for your promtness and speedy work for shipment.

took of cover removed switch and replaced with new one

I removed the unit from the wall removed the top two screws holding the panel above the door I the two screws holding the control panel removed the three switchs I found the top one to be blown and replaced it

Removed control panel first then removed bracket holding door switches 8 screws total very easy fix ????

Looked at schematic to see which parts became active when the power button was pushed. From there used meter to determine diode was open and capacitor was shorted. Biggest trouble was dis-assembly/assembly required to get to electrical parts.

Removed 6 screws from the front and back of the bottom of the unit. 3 screws each side. The panel will swing down. Remove the wires from the motor. Remove the one screw from the old
motor. Insert the new motor and reverse the procedure.
DIY will save you a $ 95.00 GE repairman labor bill, plus the cost of the motor. I repaired the problem for less than $25.00!

After researching on line and watching installation videos, ordered all three switches and installed. Disassembly of microwave was simple, removing the bracket holding the switches was a little tricky, it sits behind a metal post and you have to angle and wiggle it out. One note of caution when replacing all three switches, be sure to install correct switch in correct location. Had two of one style switch and one of a second style, and put one in wrong place, causing microwave to power up again when door was opened. After thinking it through and doing a second disassembly, and double checking installation instructions, corrected problem and microwave now works fine.

Slowly and carefully to protect bulb