Models > CUE840 > Instructions

CUE840 Maytag Range - Instructions

All Instructions for the CUE840
76 - 90 of 209
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Needed replacement oven rack.
Part was perfect fit. Good product, good value, great service.
Parts Used:
Oven Rack
  • Bobby K. from Huntsville, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner receptacle failed (stove over 30 years old)
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Parts Used:
Surface Burner Receptacle Kit
  • BETH from COUNCE, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement of elements
Simply unplugged the old elements and inserted the new ones.
Parts Used:
Delta Frame Surface Unit - 8 Inch Delta Frame Surface Unit - 6 Inch
  • Starla from Tomball, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The 6in burner would go to max heat regardless of the setting.
Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above
Parts Used:
Surface Burner Switch - 240V
  • James from Dunnellon, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner cartridge terminal broke due to electrical shock. circuit shortage caused the problem.
dissembled the burner, remove the broken blocpk and bad spade.rewiered and assembled the burner.
Parts Used:
Range Burner Cartridge Terminal Block Cartridge Male Contact Spade
  • Ge from Solon, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Renters removed leveling legs from refrigerator. I don't know why!
I tilted the unit back enough to scew the new legs into the threaded holes.
Parts Used:
Refrigerator Leveler
  • Don from Frankfort, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were a mess
Replaced the drip pans
Parts Used:
Drip Bowl - Chrome - 8 Inch Drip Bowl - 6 Inch
  • Chhristopher from Houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broiler pan missing
ordered new broiler pan
Parts Used:
2 Piece Broiler Pan
  • RAYMOND from JACKSONVILLE, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner had one temp. hot
Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!
Parts Used:
Surface Burner Switch - 240V
  • James from Charlotte, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were in need of replacement
No brain surgery required. Removed electric burner, put in new drip pans. Voila! Good for many more years of service looking like new.
Parts Used:
Drip Bowl - Chrome - 8 Inch Drip Bowl - 6 Inch
  • JOANNE from MONKEY ISLAND, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
center piece of the heating element broke off
so easy, just ordered the part, the part came and inserted the element into the stovetop
Parts Used:
Delta Frame Surface Unit - 6 Inch
  • Elaine from Atascadero, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned out burner
Pulled out the old burner and plugged in the new!
Parts Used:
Drip Bowl - Chrome - 8 Inch Drip Bowl - 6 Inch
  • Esther from Alexandria, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The broiler would not heat. I saw a bad place in the element. Ordered a new one.
Received the new one. Installed it in 15 minutes. Thanks for the fast service.I will buy from you guys the next time I need a part ! Thank You, Henry
Parts Used:
Broil Element
  • Henry from Smithfield, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
8 inch element not heating in cooktop
I removed the old element. I then plugged the new element in place. Simple repair, no tools required. Turned the cooktop element on to test for proper functioning. It heated properly. Repair completed.
Ordering the part was easy and it arrived within 2 days. Very happy with Parts Select service.
Parts Used:
Delta Frame Surface Unit - 8 Inch
  • LouAnn from Maquoketa, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner would not turn off
It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
Parts Used:
Surface Burner Switch - 240V
  • Randall from Colorado Springs, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CUE840
76 - 90 of 209