CU230 Jenn-Air Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
worn out / burned grill and components
very easy - not really a "repair" more of a face lift, although the grill was unusable.
Parts were perfect - Used it the same night.
Parts were perfect - Used it the same night.
Parts Used:
-
Brian from Lafayette, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electric barbecue element not heating
1. Diagnosed problem = switch at fault not element
Made a diagram of wire positions on faulty switch
2. Ordered part = remarkable service! Switch arrived in less than 24 hours
3.Installed new switch
4. Tested appliance = success!
5. Saved $150 and a lot of aggravation
Terrific site. Excellent help in figuring out and solving the problem. Two thumbs up!
Made a diagram of wire positions on faulty switch
2. Ordered part = remarkable service! Switch arrived in less than 24 hours
3.Installed new switch
4. Tested appliance = success!
5. Saved $150 and a lot of aggravation
Terrific site. Excellent help in figuring out and solving the problem. Two thumbs up!
Parts Used:
-
S.. J. from Punta Gorda, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switch inoperative
Remove cover plate, install new switch, replace cover place. Replace one wire at a time, a pair of needle nose pliers may be helpful. Surprise of this job was that I had a torque screw driver (I think that's what it's called) to remove the switch from the cover plate. These are the screws you'll see after removing the knob. Find that driver before you begin, mine was in the garage and for the life of me, I can't remember why I ever had one in the first place.
Thanks for a great web site!
Thanks for a great web site!
Parts Used:
-
Rex from Schaumburg, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Sockets for the burner elementss were burned out
I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.
Parts Used:
-
Martin from Manchester, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
control switch was no good
I remove fore screwsfrom the front panel. Then remove two screws to remove the switch and removed the wire plugs then put everything back together again.
Parts Used:
-
Valentine from Bow, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
electric element would not function
2 screws to remove
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
Parts Used:
-
david from castle rock, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My drip pans had rusted and I had a hole in one of them.
I just pulled the electric element out of the slot and dropped the drip pan in place and slipped the electric element back in place and it was ready to go. It looks almost new. We built a new house in 95. It took 17 months to build it. I got the stainless steel cook top that you can have the grill on one side or you can pull the grill off and slip in the burners. It is only 4 burners but it is plenty to work with. It has a down draft.
Parts Used:
-
Bobby from Paragould, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
damaged grill grate
Not much to tell about installing a new grill grate.
Partselct.com was very prompt and efficient in sending out the part.
Partselct.com was very prompt and efficient in sending out the part.
Parts Used:
-
Elaine from N.Eastham, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner drip bowl was too soiled to clean
couldn't find replacement in our town, which is quite
small and no Maytag dealers. So, I ordered on line two drip bowls and saved one"just in case"
Mission accomplished. Thanks allot.
small and no Maytag dealers. So, I ordered on line two drip bowls and saved one"just in case"
Mission accomplished. Thanks allot.
Parts Used:
-
joyce from sequim, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Infinite Rotary Control Failed
Replaced one of the four burner control switches on my Jennair cooktop. One of the tricks I use to prevent mistakes is putting the new switch along side the existing one and swap one connector at a time over to the new switch preventing any confusion and negating any need to mark the wires. This differs from your video assistant who disconnected all the wires at once.
gc.
gc.
Parts Used:
-
George from Centreville, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rusty existing parts
Unplugged the burner units and replaced the drip pans. Five seconds time per burner.
Parts Used:
-
Michael from Walpole, NH
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Sparks shot out from under knob, then, no surprise, the burner didn't work
I've ordered parts from you twice now, and both times the service has been absolutely amazing!!!!!
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Parts Used:
-
Charles from Bourbon, MO
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
back burn would turn high no mater where you set the control knob.
Well I was just guessing the controll switch was bad so I ordered a new one. So I cut off the power and held the switch close to the old one and changed the wires one at a time matching the connection terminals and cut the power back on and presto it WORKED..The service man wanted to charge me 65.00 dollars just to check it out. I figure I saved about 100.00 dollers plus I learned something.
Parts Used:
-
William from Valley Grande, AL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
one of the four burners was not working
Very simple---shut off the power, removed six screws, detached five wires, replaced control switch, put everything back together, turned on power and made husband happy!!!
Parts Used:
-
Amy from Rosebush, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
could not adj. temp. stayed high all the time
-
Don from CARROLLTON, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!