Models > CTW100FW1 > Instructions

CTW100FW1 Crosley Washer - Instructions

All Instructions for the CTW100FW1
61 - 75 of 112
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burning rubber smell
Poped up top, removed front pannel (2 phillip head screws) observed failed belt. Replaced belt. Tensioner can be held back by hand so it was easy. Works great. Part Select Rocks! I put in the model number and bam, there was my needed part, 3 days later it was in my hands. This was after me wasting time driving around town trying to find it at home depot type stores to no avail. I'll never do that again. This website makes repairing appliances a snap. Gotta love on-line shopping! woo hoo
Parts Used:
Drive V-Belt
  • Lewis from Thornton, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stripped threads.
Replaced the part in about 30 minutes. Easy fix
Parts Used:
Water Inlet Valve
  • THOMAS from Zephryhills, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain pump stopped
I just pushed the washer on its side on a price of wood. I put a pan to catch the drain water.It was then as easy as detaching two boots and two bolts that hold the drain motor on.Do it in reverse and you got it.Oh first don't forget to unplug the electrical wires ect.
Parts Used:
Drain Pump - 120V 60 Hz.
  • Kevin from Dekalb, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking drain pump
Replaced drain pump using this walk through. Different models, but pretty straight forward.
Parts Used:
Drain Pump - 120V 60 Hz.
  • Michael from MEDFORD, OR
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dirt particles on clothes
I had to remove agitator and clean under it.
Parts Used:
Agitator Screw Agitator Spacer
  • Frank from Ormond beach, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Socket set
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer tub enables after end of spin cycles
Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself.
Parts Used:
Vertical Spring - Short Suspension Spring - Long Horizontal Spring
  • Celeste from YAKIMA, WA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Off/on knob broke
Pushed the new knob into place.
Parts Used:
Control Knob
  • Barbra from Mills River, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain pump froze during subzero temp
Just like the video said in the parts menu remove front of washer remove 2 screws remove 2 hose clamps replace pump replace 2 screws replace hoses and clamps and front door to washer done
Parts Used:
Drain Pump - 120V 60 Hz.
  • Buford from LAWTON, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
belt broke
Removed old belt. Installed new belt.
Parts Used:
Drive V-Belt
  • Dave from Murrieta, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
6 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor burnt out
my husband did the work he can fix anything.i watched he explained what he was doing and how he was getting it done.it did"nt take long at all.the biggest problem was setting the belt tensioner . its running great!!!!!!!!!!!!!!!!!!!!
Parts Used:
Drive V-Belt
  • ANNA from STATEN ISLAND, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Wrench set
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive block fitting problem
The drive block spline was loose in the Agitator, for the now block to fit tight enough to stay in place while reassembly of the Agitator, ( keep falling out) the old block had to be driven out. Had to design a wire tool to hold the block in place until the Agitator could be fitted over the shaft and seated tight on the shaft drive, then pulled the wire out. Wasn't the most easy task to do and sure took more than 5 min. to install.
Parts Used:
Agitator Drive Block
  • Barbara from Calexico, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
broken washer door switch
piece of cake once i could get to it.
Parts Used:
Lid Lock Switch
  • paul from kingwood, WV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replace belt
Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off
Parts Used:
Tension Idler Pulley
  • Gregory from Piscataway, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
The water would not drain or spin out all the way
Had to take the front and back panel off the washer. A couple of clamps and electrical plug in came off and then the motor. Put the new motor on plugged it back in and put on the clamps put the panels back on and was able to wash a load of clothes. It is now quiet and spins the clothes out as if it was brand new.
Parts Used:
Drain Pump - 120V 60 Hz.
  • sherry from ellenburg depot, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer Dryer Combo. Washer would not agitate.
Checked drive belt by removing two screws on the BOTTOM of the front panel. Would spin dry but not agitate. Motor is two directional. Spin one way, agitate the other way. Same belt, so not the belt. Removed the agitator and the drive was turning but not the agitaor. It APPEARED that the agitator drive block was part of the agitator. IT IS NOT. Tap out the drive block,(Part # PSii52574)by threading a long bolt with the same threads as the screw that held the agitator to the drive assembly. Gently tap and the drive block will drop out. Replace the Agitator drive block. Worked like new for $21.32 + SH. The old agitator drive block was broken in pieces thus not allowing the agitator drive to turn the agitator back and forth. Did not need the Agitator, agitator screw or agitator spacer. Easy fix. No experience necessary. Cliff
Parts Used:
Agitator Screw Agitator Agitator Spacer
  • Mary Lou from Rangeley Plantation, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CTW100FW1
61 - 75 of 112