CSX19LABEWH Hotpoint Refrigerator - Instructions

After easily finding the lower hinge here through Google, I paid about $30 w/shipping and had the part in 2 days. My Hotpoint fridge was made in 1987, but it still runs well...why not fix the door?

Part repair couldn't be easier. No instructions needed...just empty the fridge door of food, remove top hinge, replace bottom hinge and plastic bushing, and reverse order to button everything up.

PartSelect.com did a great job supplying a high-quality replacement hinge for my old fridge, and it's got a new lease on life now!

My right door (food door on side-by-side) stopped closing - I found pieces of the plastic washer (cam riser) on the floor. After reading the stories on the web I decided to order the new part - and YES there are many universal parts that work for Kenmore/GE. The part comes with two parts (hinge and cam riser) - you should install both to insure a good fit. I took 3 blocks of wood and a shim and supported the bottom center of the door, unscrewed the hinge off and dropped it out (3 minutes). The "only" tough part was unscrewing the cam riser from the bottom of the door - it required a very small socket and you will only have about 6-8 inches of work space. Be sure you have a socket that fits before you take the hinge off. The entire repair took less than 30 minutes and contrary to some of the posts, you DO NOT need to take the door off. Good as new again!

Remove the hinge cap on top, the loosen the bolts, remove the hinge. Pick up the door from the lower hinge, lay it down and place the cam riser on the lower hinge. Replace the door, install the top hinge and check the alignment and you are done.

Supported the door on the bottom them removed the 3 screws holding hinge to door. Installed new hinge assembly. Had a litle trouble installng screw in bottom of door due to alignment issues with cam & metal piece. It finally went in when I loosened 2nd screw in bottom of door.

removed the door hinge assembly & replaced it with the new assembly.

Part was easy to find on website. Part was delivered quickly. Reapir was easy, just replaced old hinge with new hinge.

Disconnect the broken one and install the new one

The repair stories for this part are helpfull. The only problem I came accross was figuring out which part I needed to order. The parts diagram only showed one part labled 230, but when I used the drop down box to order the part there were 2 parts labled 230 for 2 diffrent prices. I called ge customer care and found out the less expencive part listed as 230 does not come with the wires etc. . The more expensive piece has the wire harness and every thing needed. I went with the more expensive part and it was a snap to install. . . .

Take off the panel in the freezer side to expose the heater, defrost all the ice. Remove the screws that hold the heater in place and remove the wires from each end. Plug in the new unit and replace screws. Replace screws in the freezer panel, to complete the instulation. It will take the most time to defrost the ice, and clean up the water. To help defroct I used my wifes hair dryer. (She did not know it)

removed door, removed old cracked riser aand replaced with new. You have a easy to follow parts site and very good prices. I will use you for all my future repairs.

Easy

After recieving the part overnight (Very unexpected speedy delivery!) I propped the freezer side door up with a 4x4 and 2x4 and the old part came right off and the new part went right on with no hassels, Done in less than 15 min!!!!
The new part even came with step by step easy to follow directions.

I removed the top hinge, lifted the door off the bottom hinge, rmoved and replaced the bottom hinge assembly, and reinstalled the door. I then aligned the door and reinstalled the upper hinge. The fridge works just like new!

Since the original part was a single element we had trouble locating the part we were replacing since it was replaced with a dual heater. Once located the repair went pretty well. We followed one of these wonderful postings that helped work through the difficulty.

1. Unplugged refrigerator from wall power socket.
2. Removed the 2 1/4'' screws and removed the back panel in the freezer section
3. Defrosted all of the ice off the coils and heater using a blower dryer which took about 10 minutes and lots of towels.
4. I replaced the defrost heater by following the provided instructions. I had a single element defroster which was replaced by a double element defroster. The instructions provided showed how to modify the wiring and were simple enough to follow.
5. Installed back panel and plugged in the refrigerator.

I checked on the defroster 1 week later and was pleased to see no ice on the coil. Problem solved.