CRSS262QB2 Crosley Refrigerator - Instructions

Replaced the Triple Water Valve

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Looked at video on how to remove and reinstall support and followed the instruct ions

After checking the capacitor and 3 in 1 starter run relay for continuity and both measuring , I was able to remove the old parts and install the new parts for the refrigerator after unplugging the unit. I also checked the new parts prior to installing. I also went on Parts Select and watched some very helpful videos. Thanks a lot for your help desk for going above and beyond to ensure that I ordered the correct part! ????

The most difficult task for me was getting old gasket out. I did call for repair help. The service person was most helpful. After almost giving up, one more tug and the gasket started coming out. Next step was cleaning the area. Aligning the gasket correctly made installation easier. I realized right away that I needed to start in a corner. The gasket went in without a hitch. My freezer is like new again. Next installment will be the refrigerator.

So simple! I just slid the drawer out of the old frame, inserted it in the new one, and added the glass cover.

REMOVED THE DRAWER, LIFTED OFF THE GLASS, REMOVED THE BROKEN SLIDE, AND PLACED THE NEW SLIDE IN THE PROPER SPACE. REPLCED THE GLASS SHELF TOP AND THE DRAWER. PEICE OF CAKE

I unplugged the refrigerator and removed the back panel in the freezer. Here the coils were covered in a block of heavy frost. The coils needed to defrost, I allowed this to happen of the course of a few hours. Once this was done I used the wire cutters, cutting the two wires to the thermostat. Doing this I checked the continuity & got no reading. Having ordered the part at a more than reasonable price including 2 day delivery, I was ready to complete the repair. Stripping the thermostat wires connected the the freezer unit, I attached the two wires color to color to the new thermostat. Here I needed to insert both ends into the connector (butt end), crimping both sides. Making sure each end I'd secure. Do this for both sets of wires. Placing the new thermostat back on the the cooper coil (on the same one it was removed from), put the freezer back in place. Here I only screwed in two, in case I need to go back in. I plugged the refrigerator back in turn the settings back to default or factory. Allowed the refrigerator to come back up to temperature for 24-48 hours. I did these and I'm glad to say my 12 year refrigerator is working just like before.

Followed instructions for this part from this site and things went well.

turn off ice maker, unplug electoral connection, under bottom of ice maker, remove two screws (hex) under bottom of ice maker, lift up on it to unhook it, take it out. (dump out all ice ). remove back plate on back of ice maker (two screws), the solenoid is held in place with two brass screws, remove them, then remove ground wire from solenoid and two wires, that connect to it,(make a note of how wires go back !). put it all back together and your good to go. . i dont think its really the solenoid that goes out, its the housing that encases it, and you have to buy another solenoid thats encased. good luck

Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.

Removed ice tray, disassembled ice tray assembly and crusher housing making sure to note the spring location, spring etc, installed new plastic housing making sure to reinstall the spring properly and the fixed crusher blade into the notch cutout., reassembled ice tray.

I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure

I unplugged the fridge and removed the dispenser's drip plate. There are 3 screws holding the front fascia. I carefully slid the fascia up to removed it. I unplugged it from what looks like a circuit board from the dispenser. Remove 3 more screws that held the board exposing the ice dispenser's hole and the water actuator. To give myself a little more room to work, I disconnected the board from the fridge. Attempted to removed the water hose but i couldn't, but found out didn't need to. I used a longer philip's screwdriver to unscrew two very small plates that were holding the actuator in place. Need a magnitized screwdriver for this, my hands are too big to reach in there. It took about 15 minutes. NO extra parts or additional parts to order.

I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!