CRSS262QB2 Crosley Refrigerator - Instructions

This is the second time I've had to replace the crisper cover, so I had that step mastered. As before, I took the glass from broken crisper cover and dropped it into new cover in seconds. Had to use a screwdriver to pry old crisper supports from the walls of the fridge. This was the only hassle. Popped new supports in, replaced crisper covers, and slid crisper drawers back into place. From now on, I'll have to be more careful about how much weight I put into crispers.

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

Twisted replacement bulb into place easily. Let there be light!

Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

Remove power from refrigerator. Pull out the drip tray below paddle. Removed the 3 screws behind tray. Gently pull control panel out and remove the ribbon cable plug from panel. Set panel aside. Remove three screws holding panel housing to door, then pull out housing slightly and disconnect harness plug behind left side of housing. Pull housing out 3-4 inches. Look at the way paddle tabs engage ice dispenser switch mechanism. Remove the left paddle hinge screw and plate and loosen the right hinge screws(these also hold the water paddle hinge) Remove broken paddle by pulling out from right hinge plate and down. Install new paddle under right hinge plate, engage new paddle tabs correctly onto dispenser switch, install left hinge plate and screw, then tighten hinge screws. Reconnect harness plug, reinstall 3 housing to door screws, reconnect ribbon plug to control panel and reinstall panel screws. Reinstall drip tray. Reconnect power to refrigerator and check operation of ice and water paddles.

At first glance I didn't see the screws that would permit me to get to the actuator but I lifted the small tray at the bottom and there were two screws. Everything went easily.

The parts arrived much quicker than expected. The parts were exact matches and they snapped into place within minutes.

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

I ordered a new shelf and I put in, less than minute

I removed the ice container found the part # on the bottom ordered a new one and installed it. It just slipped right in to place.

Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

This was a replacement part, a simple snap in. What really impressed me was the PartSelect web site and the ease of locating the part and making sure it was the right one. Finally, the price beat out all the others. Since this tray looked like others on the same unit, I needed the details, the different view angles and dimensions to make sure it was correct. No other web site was even close in ease of use or in providing such details. I know I won't waste my time at PartSelect and I've always gotten the right part at the best price.

The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.