CRSH238MS4 Crosley Refrigerator - Instructions

Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was

Took out old replaced with new. Now it makes ice

The repair went easily after watching the video, took me less than an hour to complete the repair.

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23

Removed and replace solenoid manifold valve in rear of appliance using inadequate You Tube video. Removed and replaced augur motor after dismantling various housings using a seriously mistaken You Tube video. The latter video informed us that the yoke that screwed on the motor's shaft was a reversed Left Hand thread. It wasn't at all, and we struggled to figure that out. The people that make these videos leave out steps that they thunk are obvious, but aren't at all.

Remove ice drawer ,Removed front of drawer 4 screws ,Removed broken crusher 3 screws Ordered new parts reassembled replaced fix blade spacer that was broken and blade cover housing reattached front of drawer !

Followed the video for this repair. Only issue was that the videos showed that when the front panel is removed, there is a wire harness that has to be unplugged from part No. 38c. This was not the case. What I had was a Ribbon Cable Harness that plugged into the front of part No. 38 and the top of part 38C (the two power boards) I tried to disconnect it from part 38C by pulling it out, and apparently damaged the Ribbon Cable Harness. Later found a video showing how to remove this item properly when replacing power boards 38 and 38C. Have ordered a new cable from GRP and hopefully this will solve the problem, as there is no electrical current to the dispenser controls and the ice and water dispenser are not currently working. Would have been nice to know that there are two types of connections between these power boards; a cable harness that unplugs from 38C or a Ribbon Cable Harness that unplugs from from the face of part No. 38. Hopefully I have not damaged either of the boards or anything else. Professional repair man coming on Thursday to test the boards, micro switches, etc. The boards are quite pricey, ($550.00 for both) and since the refrigerator was manufactured in 2004, we will buy a new one before we pump any more into this older unit. Very important to know how to unplug this Ribbon Cable Harness from the boards before proceeding ! Plug in on 38C is very tricky and you will need to review a video showing how it is done.

DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.

Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

First I watched the video that provided - extremely helpful - thank you- when the part arrived I removed the drawer and shelf - unscrewed the screw- pushed the slide catches to one side and removed - then I screwed new slide on - pushed to lock in the catches and DONE! That simple - EASY PEESEY!! THANKS SO MUCH FOR VIDEO AND SUPER FAST NEXT DAY SERVICE - AMAZING HOW FAST!! WILL USE ANYTIME I NEED PART AND HIGHLY RECOMMEND YOUR SITE! TIME- 5 MINUTES TOPS!

i ordered a replacement, and when it came in i took the old part off and installed the new dispenser. it works great.

New part fit nicely in an instant. Only issue is that it is a white replacement part and ours was clear...not a big deal because this is the bottom drawer so you really don't even notice.

The part arrived in about 2 days! The right side support that is attached to the inside wall of the refridgerator, that holds the crisper guide, broke apart and would not support the crisper. We took everything off of that shelf and took out the crisper and the glass that is on the shelf. We then carefully pried the support from the interior wall (it was a slow tedious move to be sure we did not damage the wall of the fridge). We made sure all of the pieces were out and snapped the new one into place. For some reason the old one did not want to come out. It broke into many pieces and we carefully pulled all of the little pieces out of the notches

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

I received the part and slid it down the molded runner and secured it.