All Installation Instructions for General Electric Range CGS990SET5SS

Part does not look like the part that needs to be replaced

I have no clue what wire goes where because there is no thing to refer to or instructions of any kind . I have not been able to install the part.

Parts Used:

SPARK MODULE 6+0 KIT

P from FULLERTON, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven sensor not working

Very very simple repair!!!!! Works great!!

Parts Used:

Range Oven Temperature Sensor

Mary from TUCSON, AZ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water would fill washing drum when off

Remove and replaced water valve, seems to have fixed the problem

Parts Used:

Knob Dial Skirt

joseph from SECAUCUS, NJ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Gas Oven will not light

I was disappointed with this parts recommendation..neither part solved the problem, a first with partselect. The Range Oven sensor change out was easy and straight forward once the back lower panel was removed. The SPARK MODULE was time consuming..the module is located and accessible only by removing the range top. Having gas burners requires unscrewing all the burners before tipping up the top and removing it, then removing the guard over the Module is next..it's a project, sure wish it worked when I was done!..turned out to be the oven glow bar....

Parts Used:

SPARK MODULE 6+0 KIT

Range Oven Temperature Sensor

Daniel from NASHVILLE, TN
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

stripped control knob

remove and replace the same .

Parts Used:

Burner Knob

michael from milford, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken Probe Sensor

Replaced it

Parts Used:

Meat Probe Thermistor

Michael from Tucson, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the original knobs were plastic and cheap and cracked within a year

pull off old ones, which wasn't hard because they were cracked. push new ones in. Some were a little harder than others but all went in with a little push.

Parts Used:

Burner Knob

Sandy from Mt. Bethel, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

The Original burner broke

Just push the burner knob in.

Parts Used:

Burner Knob

Gloria E from Walnut, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Oven lights were burning out regularly

Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.

Parts Used:

Oven Light Housing

Douglas from Thornton, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

Thank you for voting!

Replace medium burner for gas cooktop

Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.

Parts Used:

Burner Head - Medium - 9500

Charles from Houston, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Burner would not ignite.

Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.

Parts Used:

Burner Head - Medium - 9500

John from Los Angeles, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Broken plastic burner knobs provided by G.E.

Slide new, better quality knobs into place.

Parts Used:

Burner Knob

Beverly from Dana Point, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

Parts Used: