CGR1110ADQ Magic Chef Range - Instructions

I opened the door partway to remove the door. Then I removed the bottom heat shield plate by pulling it towards me and lifting it up. I removed the two screws holding on the igniter, then with the the disconnect removed the old ignitor. I plugged in the new ignitor, replaced the screws, replaced the heat shield, replaced the oven door, and was done in ten minutes.

Replacing the vertical mount igniter was very simple. Remove 2 srews and one plug. I did pull out the oven to unplug te igniter. The process could not be easier.

1.) Remove door from hinges (open slightly and pull up). 2.) Remove racks. 3.) Remove oven floor to expose burner. 4.) Remove wing-nut and burner cover. 5.) Remove two ignitor mounting screws. 6.) Pull wires and connector through back wall. 7.) Connect new ignitor and mount to burner. 8.) Replace components in reverse order.

Broke the same day I installed it

1)Completely removed racks, oven bottom and broiler drawer to access unit. 2)Shut off gas supply by by pulling horizontal lever on left side of safety valve forward to close valve. 3)With screwdriver, removed heat shield covering safety valve and connector from igniter. 4)With socket wrench, removed the two mounting screws on igniter. 5)Installed new igniter, connecting to safety valve. 6)Turned on gas supply by pushing horizontal lever to left of safety valve back to open valve (see step 2). Turned on oven to test. 7)Upon gas igniting, shut off oven and install oven components in reverse order.

removed oven door and shelves and lower pan and replaced igniter

took oven door off, took oven racks out, removed heat sheild, took 2 nuts off ignitor, removed ignitor, gently pulled ignitor wire out from back of oven, unclipped wire, clipped new ignitor to wire harness, replaced nuts to install new ignitor, replaced heat shield. replaced oven racks, replaced oven door, tested to make sure oven lite, took about 10 minutes!!

I have worked in maintenance field most of my adult life and all aspects and to change the oven door gasket was no challenge what so ever. It took longer to find my needle nose pliers to remove the old gasket clips and then re-install the new gasket. Maybe 10 minutes total

finished removing door seal, used pliers to remove old securing studs. positioned new seal and pushed securing studs into existing holes and was done.

Removed oven bottom. 2 screws and igniter was removed. 1 screw for back panel unplugged igniter.

Hello,

Your website and prediction that this replacement part was the problem were exactly correct. This part was easy to remove and replace, it is the starter for the oven so it comes with a heating element and a built in connector. I simply pulled the old wires up, unhooked the connector and removed the two mounting screws. Plugged in the new part, pushed the connector back down past the insulation, re-installed the screws and turned the oven on and poof, it started up again. We have also noticed that the oven stays hotter now, just like it did when we bought it.

Thank you very much for the advice and for supplying the correct part. A $65 part is much better than having to buy a $500 new stove/oven. We are very happy we found you and will use you again should some other appliance break down.

Sincerely,
Jim Arao
Seaside, CA 93955

Replaced igniter, removed inside bottom cover 2 screws,removed igniter 2 screws & unplugged igniter from back of oven after removing plate with 1 screw. Could not have been any easier took less than 10 minutes. And doing business with PartSelect was great, would recommend and use again any chance I get.

removed two screws from ignitor, pulled connector from hole behind it, replaced ignitor, reconnected. tried the oven and it worked first time. easy, easy.

Popped in there real quick. Wish I would have done it sooner, my oven heats up much faster.

I called the yellow pages repair man and he quoted me $450 to replace the igniter. I did it myself for $63 and it took 10 minuet's. I'm gonna get a T shirt that says "Mr Fix It" Next is the refrigerator door gaskets! Someone from part select had mentioned that to take the door off the oven you "just open the door a little and lift it off". that was a helpful hint because I would have been looking for screws for half a day!