CGEF3034MFD Frigidaire Range - Instructions

The youtube video clearly described how to remove the back panel and how to replace the probe.
The repair took maybe 20 minutes to complete and 1/2 of that time was spent cleaning behind and underneath the range!
Range is working perfectly now!

Very easy just had to pull the wire up that holds it secure.

ordered control board from PARTSELECT if you need it fast over night it remove rear of back guard with NUTDRIVER 4 phylips screws hold the control board in place it helps if you have a phone to take pictures to see where the wires go when you connect them to the new board the overlay is not to hard you have to make sure to start at one end and get the end lined up use your fingers to feel the edge of the control board at one end put overlay in place and gently lay it in place and start laying it down slowly making sure it is going strieght once your at the other end and its down i used a soft cloth to press it down across the face and happy to say the syove is working once again

I looked up the problem on YouTube and it said it was the oven temperature probe was going out. So I ordered the probe and it was shipped out, received within two days. Took out a few screws on the back of the stove installed it, put it all back together and it’s working perfect.

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.

I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.

I was actually replacing an EOC and it did not state anywhere that I might need this. In the end I did, the new board is not compatible with the old overlay and I had no idea so intended to re-use the old one. I had to wait for the new one and it worked fine. The EOC had actually been damaged by a power surge and it was obvious it was bad. I was actually hoping that this would resolve a temperature drift issue but it did not.

The repair was easy. We removed the door with the lever on both sides of the door. Unscrewed four screws and inserted the new glass. It took about 45 mins. It worked perfectly.

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.

removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.

I watch you tube of how to repair to gain my confidence and attempted the project. It was fairly easy. I took photos of wires so I wouldn’t make any mistakes. Boom ! Finished and works like a charm!!

I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.

Many thanks to PartSelect for their comprehensive website and fine service.