CFRP5NFDASS General Electric Refrigerator - Instructions

Remove back panel on bottom of fridge to access compressor area. Remove screws from water solenoid and water valve and push to the side so the side of the compressor can be accessed. Then locate the inverter box. You will find a Phillips head screw on the bottom of the inverter. This is the only screw that hold the inverter in place. Remove the screw and tilt the inverter box forward away from the compressor, then lift the box out of the the holder. You may have to wiggle it a bit to get it out. Remove the plug that attaches to the compressor and then with the power on check your voltage coming to the compressor. It should read 120 volt. If it doesn’t your inverter is bad. Remove the other plug on the inverter box and pull the box out.
Reinstall the unit in reverse order. Use the appropriate jumper to plug into the wire connection going to box and then plug it into the connection off the fridge.
Once everything is reinstalled and before you put the back panel on plug your refrigerator back in and you should be able to hear the compressor working or feel the top of it to make sure. If it’s working you are good and can reinstall the back panel.
It will take 4-5 hours to come back to temp if it’s been off for any length of time.

It's a very easy repair. However, there are no installation instructions included with the gaskets. Per videos I watched, it recommended that the gaskets be soaked in warm / hot water to make them more pliable when installing. Unfortunately, after installing the refrigerator gaskets, there were gaps that I could not seal resulting in an interior temperature of 48 degrees. For some reason, the gaskets appeared to be puckered thereby preventing a decent seal. I don't know if the puckering was caused by the soaking. I ended up reinstalling the old gaskets.

Reviwed an existing instruction ans was surprised at how easy it was to remove the existing gasket and replace it. No tools required at all.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Removed the entire dairy shelf from door and installed the dairy door and replaced the entire dairy compartment on door

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends

I made my wife fix it.

Checked water inlet tube inside freezer, stuck screwdriver in it to see if there was any ice and it seemed clear. Checked water pressure to fill valve, good pressure. Replaced fill valve, still no water to ice maker. Replaced Ice Maker. Still no water to Ice Maker. Removed freezer back panel, hit fill tube with heat gun after allowing freezer to defrost awhile, replaced back panel, ice maker. Water going to icemaker fine. Problem was that the fill tube was frozen up way at the back where the water line emptys into the icemaker fill tube. Old icemaker and fill valve were probably OK. No real way to check it from outside the case in the rear of the fridge as the water line is sealed on the fill tube and heating it without removing the rear freezer panel does not get back far enough to melt the ice.

Pulled ice box away from wall. Took lower cardboard cover off. Shut water line off. Got my volt meter and checked the current going from the wall to the plug in at the inverter (input side), and I had the required 115 volts. Then I unplugged the connection going to the compressor (not the plug at the compressor which you cannot see until you unbolt the inverter) but the output connection side that goes to compressor. I checked the voltage and had about 13 volts not the required 115 volts. Therefore, I came to the conclusion that the inverter was bad. I ordered one from Partselect and they shipped it right away. I installed it and the ice box is back up to running order.

I replaced the water line and the inlet water valve

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Unscrewed old cartridge, ordered new cartridge, installed new cartridge by following very simple instructions. Took only one day for part to arrive from PartSelect although I paid for cheapest shipping, which was "ground." I was amazed!