Models > CFGF366DCG > Instructions

CFGF366DCG Frigidaire Range - Instructions

All Instructions for the CFGF366DCG
61 - 75 of 95
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
light bilb went out
replaced it
Parts Used:
Light Bulb
  • Denise from Landover, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
temp was not reading right
remove back panel took out old part splice wire replaced
Parts Used:
Oven Temperature Sensor
  • santa from glassboro, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
3 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob lost middle metal clamp
Received part very next day and put new knob on. Matches perfectly.
Parts Used:
Top Burner Knob
  • Holly from Tampa, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Parts Used:
LENS
  • Amy from Corona, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two of theTop gas burners would not spark
Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.
Parts Used:
MODULE
  • Robert R from Lewistown, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Parts Used:
LENS Light Bulb
  • Sharon from Foley, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove top was worn and scratched from usage and cleaning.
Very simple. I removed the three screws per burner (x4) ans used a flathead screwdriver to pry up the stove top, working from the front (clips) sides then rear.
Parts Used:
Cooktop - Black
  • Chris from Algonquin, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
oven would not stay on
remove belly pan ,pull draw out easy acsess remove screws and replace
Parts Used:
IGNITOR,BAKE
  • Mark from AuGres, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
bought a used gas range i have propane it was natural gas
changed the orfices with a 10mm socket and driver handle used an adjustable wrench to tighten the orfice in the bottom of the oven approximately 45 minutes we were using the range
Parts Used:
LP Conversion Kit
  • Vernon from Moorehead, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Door glass cracked
Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.
Parts Used:
GLASS
  • Mike from Collegeville, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
inner glass door was broken
removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range
Parts Used:
GLASS
  • Norma J from Riverview, FL
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    30 - 60 mins
Was this instruction helpful to you?
Thank you for voting!
Broken timer board
slid range out halfway . Remove top back panel, remove 4 screws in board and replaced in same order
Parts Used:
Electronic Control Board
  • Paul from Saugus, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
really bad ugly streaks inside of glass
open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.
Parts Used:
GLASS
  • John from Hemet, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
oven would turn on and stay on regardless of set point
Pulled oven from counter space unplugged unit unscrewed 9 - 1/4" tech screws then one more 1/4" tech screw that holds the sensor.Inserted the new element cut the two wire because it was a different connection stripped the wires and did the same to the old element but used the old plug.Connected the plug,plugged the over back in slid the unit back and turned out on for a test.All is well,thank you!
Parts Used:
Oven Temperature Sensor
  • robert from Mansfield, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
burner would not light
We took off all of the bolts holding the burner assembly's in place . Then took the top of the s range off. Used a wrench to remove the old assembly and re-placed it with the new one. It took longer to get all of the top and under cover off then to put the new part in. Very good service from Part Select. MATT
Parts Used:
Front Burner Igniter/Orifice Assembly
  • Matthew from Gladwin, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CFGF366DCG
61 - 75 of 95
Back to Top