CFEF317ES2 Frigidaire Range - Instructions

First I unplugged the element that wasn't working and switched it with one that was to confirm that it was the burner element, and not the cooktop wiring, that was the problem. Once that was confirmed, I ordered a new element from partselect.com. Upon arrival of the new element several days later, I plugged it into the empty plug on the cooktop and voila, we're cooking on all 4 again.

I just plugged it into the receptacle on the stovetop and turned the thing on, and it worked! I'd been without the 4th burner for quite some time. Nice to have it back!

After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

This repair was easy, but I would not have even tried if I hadn't read the tips from other DIYers - thanks! The website questions and schematic along with some common sense testing isolated the problem with the oven only heating up to 250 degrees. Since the broiler (upper element) worked ok, that made it likely that the temperature sensor was not the problem. That made almost certain that the bake (cooking) element was the problem. So, I ordered the part, which was delivered quickly. Early on the morning of the scheduled delivery date, I turned off the oven power at the fuse box and pulled the oven away from the wall. There were only 4 screws to remove in order to take off the rear panel. The bake element was attached to two slide-on connectors, one of which looked charred and partially disconnected. I cleaned the charred connector, reattached it to the bake element, turned the power back on, and then turned the oven on. The charred connection glowed, so I immediately turned off the oven and the power. I disconnected the bad connector, cut it off from the wire, and stripped the wire to prepare for a new connector, which cost 30 cents at the hardware store. The bake element connection was cleaned, and then the new connector was attached. The power was turned back on, and then the oven was turned on, and it heated perfectly. After confirming several heatings over several hours, the rear panel was reattached, and the oven was pushed back to the wall. This expensive 40" dual fuel oven had been purchased new and used for 3 years by the prior owners of our home. The oven's computer brain died when the oven was 7 years old - the repair cost us $500 for professional labor, parts, and materials. I don't know if I could have done that repair, but I had no intention of shelling that much again, which is why I tried this bake element repair myself. The oven is now 11 years old, and the most likely part to fail is the original bake element. So, we may keep the new part as insurance with the hope of making a fast, easy, inexpensive repair when the original bake element eventually fails.

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

watched a U-Tube video on this subject.....worked like aa charm!!

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.