All Installation Instructions for Frigidaire Range CFEF3019MSA

Repaired Oven Range Light Bulb

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Parts Used:

Light Bulb

Alan from SAN MATEO, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Oven wasn’t heating

Used instruction video & replaced part.

Parts Used:

Temperature Sensor

Felicia from FORT MILL, SC
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

F10 Code/ Oven Temperature not working

Removed back panels and removed temperature sensor, which was extremely easy, and replaced with new sensor. Only one hex screw holding it in place.
Replacing control board was surprisingly easy as well. Just take a photo of where all the wires connect (only two to unplug) and use a putty knife to remove the touch pad (doesn’t come with new control board). The touch pad was still sticky so it adhered to the new control board with no issues. Then plugged oven back in. Voilà! Oven worked again!

Parts Used:

Range Electronic Control Board

Temperature Sensor

Emily from MACON, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Had aluminum foil stuck on bottom

Removed 2 screws, pulled out the panel, replaced the new panel and replaced the two screws. Less than 5 minutes.

Parts Used:

Bottom Panel

George from JACKSON, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Range not heating properly

The youtube video clearly described how to remove the back panel and how to replace the probe.
The repair took maybe 20 minutes to complete and 1/2 of that time was spent cleaning behind and underneath the range!
Range is working perfectly now!

Parts Used:

Temperature Sensor

Eloisa from SPOKANE VLY, WA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Oven was over heating. In bake mode broiler would glow red and didn’t cut off after preheat

Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.

Parts Used:

Temperature Sensor

James from S CHESTERFLD, VA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

N/A

I had open back cover and remove the switch than replace new switch. Makesure cable conection.

Parts Used:

Infinite Burner Switch - Large Element

Dineshbhai from Rincon HWY21, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

My five-year-old Frigidaire Gas stove was giving an F 10 code.

I looked up the problem on YouTube and it said it was the oven temperature probe was going out. So I ordered the probe and it was shipped out, received within two days. Took out a few screws on the back of the stove installed it, put it all back together and it’s working perfect.

Parts Used:

Temperature Sensor

Tracy from Summerville, SC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Lens cover for the oven light

Very easy just had to pull the wire up that holds it secure.

Parts Used:

LENS

Larry from COZAD, NE
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Burner switch work sometime.

I follow the video on your site

Parts Used:

Infinite Burner Switch - Small Element - 240V

junius from WICOMICO, VA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Change on e of the inside glass

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

Parts Used:

GLASS

Ronald from Ozone Park, NY
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

The part I ordered has 5 connections and the part to be replaced has 7 connections. I had to ask a friend who is expert in electrical wiring to help.

My friend used a tester to determine where each wire was supposed to connect to. I'm not sure what he did with the extra connections.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.

Parts Used:

Dual Element with Limiter

Phin from HARRISBURG, PA
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

run away temp

I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.

Parts Used:

Temperature Sensor

James from ELKHORN, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

NO HEAT IN UPPER ELEMENT

NEED A QUARTER INCH SOCKET FOR THE BOLTS. REMOVE THE BACK PANEL AND THEN YOU WILL SEE THE TWO ELECTRIC WIRES GOING TO THE TERMINALS OF THE ELEMENT. DISCONNECT AND THEN GO TO THE FRONT OF OVEN AND REMOVE THE FOUR BOLTS THAT HOLD IN THE TOP ELEMENT. SIMPLY, VERY SLOWLY PULL THE ELEMENT FORWARD UNTILL IT CLEARS THE BACK AND YOUR GOOD TO GO. DO NOT FORGET TO DISCONNECT THE POWER TO THE OVEN BEFORE YOU START!

Parts Used: