CFD28WIS0 Crosley Refrigerator - Instructions

SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND

Remove frozen food and ice cubes to coolers so they stay frozen.
Remove shallow wire shelf.
Slide out both sides of slide assemblies. Defective slide unclip the front corner front frame remembering to remove the plastic retention rivet first. It has a centre pin that needs to be pulled out first. Support the rest of the frame on the bottom shelf/basket frame
There is one cap head square driver screw to remove on the wall of the freezer holding the slide in place. Leave the other two flat head screws alone. Slide the defective frame off the other two flat head screws. Take new part and attachment is the reverse of the disassembly you have just done. The front frame corner clip is a bit difficult to put together there is a top and bottom spring clip then the plastic "rivet" where you need to push in the centre pin to retain it in the joint. [a bit flimsy so be careful].
The shallow basket should be carefully placed on the front and side clips, and make sure everything is square. Then slide the shelf to make sure it goes into the freezer properly. Then you can re-load the food and ice cubes.

Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.

I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.

I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent

The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963

Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was

Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.

We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.

I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.

Basically unhooked water lines and removed the screws

I removed the defective water valve. All wiring and tubing connectios were color coded.
It connected the water tubes and electric plugs to new water valve.
The water dispenser worked perfectly after I reconnected everything.

Removed 1 screw and unplugged flipper mullion assembly and removed it. Plugged in new flipper and one screw and done. Works as it should.

After sending PartSelect the info to their troubleshooting dept. about my ice maker, they recommended replacing the ice solenoid. I did so at a cost of $102. No change, turned out replacing the ice maker(did not purchase from PartsSelect) was the issue and works fine now.

So wasted $102. FYI the part took 6 days to arrive.

first, there many different water filters. your experience will be different according to your water filter type.

Remove ice maker, completely disassemble, being careful with the styrofoam around housing. This is a very weak part and takes much load from auger. Use a white, high strength tape to bind around the housing with, (very important) or you'll be doing this again as it is a failure point.

I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.