CESP2978JQ0 Whirlpool Dryer - Instructions

So I opened the back up, and looked down the flame shoot and I could see that the igniter was never glowing red. (You can actually see the red glow of the igniter when its working right, then you here the solonoid click and flame. But again all this when its working correctly.) So anyway, no heat no glowing red.

I took the voltmeter out, grounded 1 lead and just followed the voltage (using the schematic provided), through the switches, yada yada trying to trace how far it got.

Voltage got to 1 side of thermal fuse, but not to other side. Bingo. Disconnected fuse and did continuity check - open. All of this took diagnosing took 1/2 hour to hour. Not really counting toward fix. Ordered the part at parts select. Put a jumper over the fuse so that clothes could still be dried (probably not recommended but it works). Part arrived in 2 days. Didn't even put the back panel on.

The part is right on the back. 1 screw, 2 space terminals. Takes all of 3 minutes to replace. Then another 5 minutes to put the back panel on and vent hose back on. Most of that is because you are working in a cramped space. (I don't have the biggest laundry room.)

Can't beat parts select!

Parts select + a little know how, saved me about $400.

I removed the back of the dryer, removed the single screw holding the fuse in place and checked it for continuity. It didn't work, so I placed an order and 3 days later I was back in business. the replacement took about five minutes.

this was a super easy job! i unplugged the dryer, removed the back panel, located the fuse on the bottom left side, replaced it, put the panel back on, plugged it back in and IT WORKED! this was the first appliance repair job for me and i am so glad i found this site. it probably saved me $100.00 or so doing it myself. thank you!!!

Pop out the old latch and replaced with a new one

just put the new part in the door---sooo easy! THANK YOU!

The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)

Took back panel off dryer, unscrewed old part, put on new one. Easy fix. Dryer works great again.

Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.

I opened the front lower cover to get the schematics. Looked for the most probable part that was bad. Then traced wiring from the gas solenoid to find the thermal fuse.
I opened the back. Took the two wires off the thermal fuse and put my Ohm meter from terminal to terminal. As I got no reading, I ordered a new fuse. It took about 5 minutes to replace and button the dryer back up. This is the second time I have had to replace this fuse.

After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.

The major issue was getting the dryer out and cleaning it all up. That's what took the time but it was worth it to clean out the lint in the ducts, etc.. Putting the thermal fuse was a snap thanks to the great feedback received when I got this web site and read the previous responses.

took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......

the part fit perfectly, it just snaped right into place.

Took off the backplate of dryer, replaced fuse, done.

after removing the back panel (5 screws) i replaced the heating element, (about 15 minutes, after vacuuming all of the lint and dog hair), replaced the panel, but still no heat. removed the back panel again, and replaced the thermal fuse. (2 screws, 5 min.) still no heat, so on to the thermostats. (there are 2, both in easy reach). i replaced the one in the heating element housing first, as this made sense. (it has a red stripe across it, so they can't be confused), replaced one connector, which the new part requires, buttoned it up, and presto!! the dryer works just as new! all told, i have less than 100.00 with all of the new parts. the longest part of the whole thing was cleaning all the lint and debris out first, which you absolutely must do