CEP3540AAB Magic Chef Range - Instructions

Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.

Unplugged the range, took off back shield (4 screws) unplugged the old part and plugged the new part in, put the shield back on and plugged the range back in. When you remove the light unit behind the lens after unplugging the two contacts slide it sideways toward you, it is slotted, don't try to pull it straight out or you will break the lens.

10 Minutes for a stove my landlord thought was not fixable (repairman had already cut the wires to the element and capped them)! The delivery person handed me the package, I got out the single tool needed, installed the part, put away the tool, cleaned my hands, and put a pot of water on the stove to boil for pasta. 10 minutes!

Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).

Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.

Ordered a front burner but it was not the right size. Ordered a switch after local dealer said I had a bad switch. Ordered a switch from Parts Select and received it the next day. Works good now.

Disconnect the range from wall outlet. remove 2 screws in the back of the cabinet,remove switch plug. connect back range to outlet to check if it is the switch. make sure the light isn't on. then I order the switch online at PartSelect.com and it arrived in 2 days. When I installed the piece, the problem had been solved. I hope this information will be helpful for others.

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing

Performed repairs just as you directed. Everything went in in without a hitch. All the parts fit well and seem to be working fine. Wife still complains. Maybe I need a new burner coil.

Turn off power 220v, opened cook top, remove old 8" switch and replace with one of the new switch ps2089438. However, I have another cook top, it is a 6" heating element. Can I use the same switch for 8" and use on a 6" heating element? Since I order 2 new ps2089438 switches. Thank you for your anwser. Kahn lee

Pulled stove out to unplug. Removed screws holding end covers then remove screws on the underside of cover as you face the stove top.Remove knobs.Pull bottom cover forward and up so you can lift it off to see the insides.Remove wires and attach to the new part one at a time. Unscrew old from the front and attach the new one.Put it back together.Done.

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.

ulplugged elements and dropped in new pans