CEA1M1WSTB Gibson Range - Instructions

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Simple Just plugged it in !

Probably a good idea to either unplug unit or make sure oven is in off position first, then remove screw on either side of old bake element, then gently pull out about 3 inches to expose wire connections and carefully disconnect each slide-on connector. Dispose old element in trash and replace with new one from partselect.com in reverse order. Very simple and much less expensive than either buying a new appliance(if you've been satisfied with what you have), paying a repairperson to come in and/or trying to hunt down the right part from a "local" appliance store/warehouse. The part was easily identifiable via the graphic depiction on the partselect.com website, arrived in excellent condition and in record time for normal ground shipping(less than 2 days from order date!), and I experienced kind and competent customer service from the get-go. A do-it-yourselfer like me really can't ask much more than that when it comes to appliance repair!

I pulled the range out of its space, disconnected the power cord, disconnected the two electic power wire on the heating element. Then I disconnected the two retaining nuts on the inside of the oven and pulled the heating element out. Then reversed the order and wala, hot oven and now my corn bread does not burn.

took out the two screws pulled the element out unplugged the wires, plugged in the new element, stuck the element back in the holes and put the screws back in

Only two screws to remove, so it was very easy to just pull the element out, remove the wire connectors from the old element and place on the new one. This is one repair you should NEVER call a service person for! Be brave--anyone can do this.

Open the oven door and removed a metal screw from each side of the element on the rear wall of the oven. Pull each side of the element out about 2-3 inches and you should see the terminal fitting with a spade type connector. Remove the connector from each side and discard the old element. Place the connectors on your new element and push it through the openings that the old element came out of. Replace each of the metal screws and you are done.

I unplugged the damaged element and plugged in the new one. It took less trhan 30 seconds and the unit worked just fine.

Found that knob shaft broken and unable to replace knob without replacing /timer assembly. Light fit and works very well.

Pulled out the old drip bowls and replaced with the new. A simple snap!

Just followed the instructions

Took out bottom drawer and unplugged power cord, slid unit out to reach back panel,removed front door( 2 Phillips screws) making it easier to reach back of oven, removed screws inside of oven holding element in place, took plate off rear and removed the spade connectors with needle nose pliers. Slid new element into oven and replaced screws inside of oven. Connected the two spade wires on the back and replaced rear panel. Slid unit back in place and plugged the 220v power cord back in. Straightforward and very simple! It took 3 times longer to clean the oven while it was disconnected than it did to replace the element.!

Unpluged old one pluged new one in. So good to have a burner that all the coils heat up.

remove the bottom storage door unhook 2 return spring check with flash light install support under the top cook door and open the top door slowly , remove 3 screws at the bracket slide out the hinge with springs and slide out the hinge from the door install the 2 springs the same way you take it out and reinstall bracket and screws and springs and your done just picture and remember the you remove and reinstall i did it and i'm not a handy man i got happy when i did it my self i said wow to my self if i called some repair guy he possible wil charge me at least $ 125 to $ 150 for 25 min job

Pulled out the old, and replaced. Very simple for a 62 year old woman! I cook a lot, being from the country, and Imwas so excited to get my burners fixed! Should have done it years ago! Thanks!