CDWT280V00SS General Electric Dishwasher - Instructions

remove front lower cover, 2 philips screws, turn off water supply under kitchen sink to dish washer, turn off power to dish washer, remove water supply line to valve, remove power to valve, clip ons, remove two 5/16" screws holding valve on, turn valve gently to access clip holding washer supply hose, push clip up hose and hold hose while pulling valve off. re-install in reverse order, a flash light helps.

Replacing the soap dispenser was relatively easy, But a word of caution.when I removed the front panel, as it fell off, it pulled the electrical tape out of the door. That of course ruined the electrical panel. Even better, that panel is no longer made. So unless you really want a new dishwasher, be sure you support the front panel when removing. Probably the easiest way to do that (I found out later) is to sit on the floor with the front panel on your legs as youminscrew it. Do read other reviews about how to do the repair as the part comes with no instructions and GE is of virtually no help.

Shut off water, disconnect drain line from disposer. Remove dishwasher from wall and remove water feed line. Unplug or disconnect power to unit. Remove upper and lower dish racks as well as lower water sprayer bar, and filters. Lay dishwasher down on backside (make sure to catch water with bowl). Disconnect pump connector with nut driver and replace. Stand dishwasher back up and reverse removal process

I was offered a free dishwasher for the taking. The soap dispenser latch was broken. I ordered the part, it arrived two days later by standard delivery. The door cover has to be opened and seperated. The difficulty is that the door will not stay down or up without assistance. Once open, the dispenser is replaced by removing 6 screws from within the door compartment (between the door front cover and inside door wall. Two electrical leads must be removed and reconected to the new part. Removing them is problematic, since one connecter partially chipped off using pliers to gain a grip. After inserting the new part the 6 screws are installed from behind the part and the leads reconnected. There are two ribbon connectors for the control panel and display. They did not come loose so I left them connected, which made it awkward to manipulate the various parts with the door split open. Putting the ribbons in proper place was easy if careful. Securing the outside and inside halves of the door completes the repair. I found instructions on google. This was tricky but easy, as the door parts were often trying to move out of an accessible position for working. Otherwise it was one of the easiest things I have done. It would be easier with two people, and I had only one good arem to work with due to shoulder surgery, but it was successful. The dishwasher works fine, and the price was right at $45.00 in parts plus shipping for a top of the line model.

I examined how the old gasket was attached before removing it. I then pushed in the new gasket needing no tools. There has been no water leakage since.

we followed the instructions as posted on your web site. Once the dishwasher was apart it was self explanatory. We did however need pliers to separate the wires from the old soap dispenser.

Cut power and water flow to the appliance. Laid appliance on its side, removed the electrical lead from the motor. Remove the mount from the back of the motor and loosened the two clamps- one to the sump and one to the discharge tube. Removed and replaced the pump/motor assy. with the new one, reinstalled the clamps, rear mount and electrical lead. Righted the unit and fired it up. Worked fine.

We noticed our detergent door was not opening on cue to dispense the soap and it was leaving our dishes dirty. It came to be that our spring was sprung on the detergent door. I researched it and I could either buy the spring or the whole detergent contraption (installing the contraption was one wrench easier but cost $35 more). Knowing my husband the way I do, I decided to do the more costly route. I followed the instructions from previous installers on here and me and my husband did it in 30 minutes! I do agree that it is a two man job for some of it as I stressed to him NOT to take the front off haphazardly, as it was $400 to replace that! We took the 12 or so screws off, detached the line to the detergent dispenser, reattached, screwed it into the door and replaced the front 12 or so screws again. Easy peasy! Unbelieveable!

NOTE I have classified this is a DIFFICULT JOB, but NOT because of the mechanics involved [including the electrical connectors UN-plugging and re-plugging, BUT DUE to the ANALYSIS you need to do to determine whether the SOAP DISH PART or the CONTROLLER is at fault. And this ANALYSIS will probably require you to get into the DISHWASHER DOOR twice. Once to do the analysis and then again to replace whatever part you target. Being you will want to continue to use the DISHWASHER by manually dropping the soap door [or just soap] at the appropriate time in the cycle, while awaiting the new part, which means you have re-button up the door and take it apart again when the new part arrives. . Before starting, view PartSelect's VIDEO on replacing the SOAP DISPENSER, but ignore THE STEPS OF REMOVING AND REPLACING THE SOAP DISPENSER.PART, at this time. The analysis starts with MANUALLY trying to activate the mechanical soap door release on the back of the mounted SOAP DISPENSER, with the soap door closed. It should take only ounces of downward pressure [towards the door hinge] on the vertical plastic piece in a channel near the center of the dispenser, to release the soap door. Next if you have access to an OHM METER {or MULTIMETER} or a DC POWER SUPPLY [to test the the activation of the door release] pull the two connectors on the SOAP DISH SOLENOID [a set pointed pliers will be helpful, as outlined in the VIDEO]. If measuring the SOLENOID's resistance it should read roughly 1800 OHMS. If using a DC POWER SUPPLY, you will probably need at least 25 volts DC to trigger the SOLENOID [NOTE I do not have a variable DC POWER SUPPLY to check it out nor do I know the voltage that the DISHWASHER uses]. Do not bother to measure the resistance of CONTROLLER's driving circuitry [the two wires having connectors], as it will read INFINITY, regardless of whether GOOD or BAD, The CONTROLLER apparently uses a RELAY on this circuit, as opposed to some kind of solid state switch. Replug the SOLENOID connectors. Re-buttoned up the DISHWASHER as shown in the VIDEO, assuming you are going to continue using it If you determine no problems in the above tests, then consider it a CONTROLLER pro0blem and you will need to order one. Otherwise you should have found indications of a SOAP DISPENSER PROBLEM. . When the replacement part arrives and you ready to install it, refer again to PartSelect's VIDEO on replacing the Soap Dish Dispenser for a refresher Following the VIDEO completely, if you replacing the DISPENSER. If you are replacing the CONTROLLER, once inside the DOOR, you will need to remove around 6 individual electrical connectors [before doing ANYTHING REMOVE POWER from the DISHWASHER [as instructed in the VIDEO}. These connectors [all but any single wire connectors] are designed to be plugged only one specific way, so when re-plugging NEVER FORCE a connection, The best way to make sure you do not get confused, take a picture of all the connectors -OR- make notes on the looks and orientation of each multi-wire connector. There is one mounting screw on right side of the CONTROLLER. When installing the new CONTROLLER there are mounting EARS on the left side that are first engaged by having the CONTROLLER tilted up on the right side. Replace the mounting screw. Replugged all the connectors using whatever guide you made. Proceed to put the DOOR back together as outlined in the VIDEO.

Used needle nose pliers to get them off.G

Replaced wax motor and soap dispenser (all one piece). Only problem was the plastic seal on the very bottom of door had come unseated, and therefore was leaking. You need to check that it is snapped all the way in, and then the leak ceased. Took me a few tries, which made a ten minute repair into an hour long one.

Water was leaking from under refer next to installed under counter dishwasher. Once determined to be dishwasher not refer I removed dishwasher toe place was able to see dripping inlet solenoid valve. I had to disconnect 11V power, shut off inlet water, disconnect inlet water house and remove dishwasher from under counter. Once dishwasher was in center of kitchen I flipped it upside down and removed the electric solenoid inlet valve. Removing the valve took one wrench to remove inlet hose then two wrenches to remove 90 degree brass fitting and another to hold solenoid. I used a nut drive to remove two screws that released the solenoid from the dishwasher frame. I used teflon tape to reattached the 90 degree brass fitting and inlet hose.

The tub gasket is very easy to replace. First I pulled out the old gasket then using the center marking on the new gasket, I centered the gasket at the top then pushed the gasket into the track. At the bottom I reused the wire that holds the two ends in place making sure I attached the separation wire in the same configuration as with the old one. I had another leaking problem with the seal on the bottom of the door. GE does not sell a repair seal for the door bottom and a new inner door must be purchased at around $200. I made that repair using an old bicycle inner tube. I cut the tube into a one inch strip and epoxyed the strip to the tub where the door meets the tub.. Worked perfectly!

very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing

After reading other customer responses I decided to attempt the repair myself. After pulling out dishwasher I turned it on it's side and prodeeded to remove the 3 screws holding it in place. FIFTEEN minutes later I pushed it back into position and it has performed like new for the past month. Comparing parts and service I saved about $200.00 on this self repair. I would not hesitate to undertake another repair after my experience.