CDU8000V Crosley Dishwasher - Instructions

I went to take the bottom front panel off and ended up dropping the screw down behind the baseboard and then found that I did not need to take the panel off. The broken end of the float was not obstructing and I was able to just drop the new float in place. I spent more time looking for a replacement screw than any thing else. Ran it and it works fine.

I followed instructions of others that were posted. Door seal was simply removing old seal, cleaning track and pushing new seal in,making sure it was even all around. Removing the door cover to get at the Dispenser grommet was simply removing all 7 hex nut screws. Had to go out and buy the proper hex nut screwdriver . I did not remove the wiring, just turned cover over to remove the two nuts holding the dispenser. The nut on the left was a little hard to get off, had to kind of force the socket onto the nut. Otherwise all went well and simply removed the old grommet and installed new one. Finding the right tools was the part that took the longest. I had hard water before putting in a water softener so that was probably hard on the seals plus the machine was an older model. No problems now and saved having someone come in and do a repair.

I removed the old door gasket and thoroughly cleaned the track. I placed the new door gasket in place- no problems.
I had to remove the 7 screws from around the door to access the old, crumbled gasket. This was accessed by removing 2 screws with a socket wrench. The old gasket pulled out and the new one slipped right in.
No more leaks!

The upper dish rack was in the way for my old body and short arms to reach the nut, so I had to pry the plastic bumpers off with a screw driver and remove the rack. From there you could almost do it with your eyes closed. Unscrew the old spray nut, screw in the new one and pop the spray arm on. Slide the dish rack wheels into the rail tracks push it closed, and insert the plastic bumpers. The only tricky part was the bumpers. You have to pry the forward-most piece of plastic away from the piece behind it. That pulls the holding edge out of the slot in the rail, and the bumper comes right out. Putting it back just takes a push from your thumb, and make sure the holding edge is back in the slot. Before I put the new nut on, I compared it to the removed one - it was obvious that the latching ring on the old one had been worn by the rotation of the Spray Arm, so the water pressure was all that it took to push it off.

I opened the dishwasher door, then used the Torx bit to remove the screws all around the edges of the door, and removed the inner part of the door. Then I removed the long metal plate at the part of the door farthest front (with the door open) and the large black plastic housing. The metal plate then became a useful tool to brace at an angle between the door and the body of the dishwasher. This not only held the spring-loaded door down, it also held the inner part of the door up against the body of the dishwasher.
One nut held the latch assembly to the door; I removed it with the nut driver.
On the latch assembly, there are two small plastic catches that keep the latch from sliding out, I held those out of the way with a blade screwdriver and slid the latch out.
The new latch then snapped into place, and I assembled the door again in the reverse sequence of disassembly.

Turned off water at valve, removed float switch, removed water inlet vlv. Replaced and reassembled. Still not water going into the machine. I have no voltage to the valve or float switch. I then took the door apart to find there were burnt wires as well as a burn mark on the control panel. Upon closer inspection, it looks like the door seal has failed and water got into the door. Had to replace dishwasher with a new one.

I simply connected the two hoses to the valve plugged in the two wires and it was working!

Unscrewed the inside door panel. Removed the reservoir assembly. Disconnected the wax motor. Replaced it with the new motor. Replaced the new o-ring. Done. The hardest part was finding out why it was not working and how to fix it. Google for a long time in order to find some idea what to do. Then took the door apart to see the reservoir and the wax motor. After that, it was pretty easy. HTH

The problem is a worn seal ring. That ring is inside the lower spray arm's spray nozzle support assembly. The wash arm spins on that assembly.

I unscrewed the lower spray nozzle popup, from the wash arm support. That part, from which the extending spray nozzle rotator pops out, simply unscrews, by hand, from the wash arm support. Then I could lift off the wash arm itself to get it out of the way for the next step.

With the wash arm removed, I could then gently pry off the flat filter cover which was underneath the wash arm (the filter cover is simply clipped on. Use a screwdriver).

Now, reaching inside where the that popup spray nozzle was screwed on, you can see and/or feel a tall skinny plastic piece in the center of it, which actually screws that wash arm support onto, well, the rest of the dishwasher.

With that "screw" removed by hand, I removed the wash arm support.

Inside that wash arm support the old ring seal can be removed and the new one inserted.

Simply reverse the process to re-assemble.

Note that it's hard to determine where, exactly, to put that ring seal, inside the wash arm support. But it seemed to me it didn't really matter as long as it was just in there.

Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.

The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.

Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.

The repair was very easy. The door gasket was a little short, but I gently streched it to the proper length. I replaced the other parts as a precaution as some others said they were really the source of the original leak. It went very smoothy and NO MORE LEAKS.

Read the Diagram on Parts Select Site and it only took me about 15 Minutes to disassamble and install the New Parts. Very Easy once I read the Schematic on the site.

Attempted repair was quick & simple. Removed 7 torx screws, and then pulled the wax motor out of its holder. Pulled 2 wires off, and replaced old motor with new motor. Reattached wires, & reassembled.
Only problem was this did not fix the problem, so back to square one, but worth a shot.

Ordered new part from your site. The new basket arrived in just a few days, without the handle and cover for the small item section. Instructions with with new basket described how to remove the other parts from the old basket and install them on the new one. Everything worked out perfectly and my silverware stays put. I've very happy!!

It was simple. My wife unscrewed the spray arm support nut and then, replaced it with the new parts. It was very simple. My wife was able to do it all by her self.