CDU2J3 Crosley Dishwasher - Instructions

I used a voltmeter to see if 120 volts was present at the right time in the cycle; it was, so the actuator was the likely culprit. I ordered one on a Monday afternoon about 2:30, and it appeared on my doorstep Tuesday, shortly after noon! It took less than 15 minutes to replace the actuator - removing the 7 Phillips-head screws, lifting the panel, popping out the upper actuator, removing the two wires, putting them on the new actuator, popping it in and putting the panel back on. Worked like a charm. Happy wife . . .

I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track.
It was very easy but did not solve the problem.
Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.

popped the two end caps off of the runners (the hardest part of the installation was figuring out how to pop them without braking them). Turns out just using a flat screw driver to start opening the cap lock did the trick. Once the end caps were off it was just a matter of rolling the old one off and the new one on and then putting the end caps back on.

The new basket wasn't an exact match, it's lighter weight and doesn't have the exact same configuration as far as the rows of tines. This will do us fine until it's time to replace the unit.

I first replaced the seal/grommet around the soap dispenser latch, which was leaking, but did not totally stop the leak. I ended up ordering the door gasket too. Both were very easy to replace. My wife wanted a new dishwasher, but let me take a crack at fixing the leak first. Woo Hoo - big $$$ saved.

The problem would rarely happen if the dishwasher was fully loaded vs. lightly loaded; which would produce a lot of water rapidly during the spray cycles. (or empty during the house inspection!). Removing and replacing the door gasket is super-easy.

Un screwed the dishwasher from the underside of my kithcen counter. Removed the copper water hose(after turning off water valves). PUlled the dishwasher from under counter to expose the hinges. Hung the new linkage on the hinge. Stetched the spring from flange on the bottom of the dishwasher to the new linkage. Reattached hose and reconnected the unit to counter top. Job done.

Remove the old rack and slip in the new one. Took 5 min to figure out how to remove the upper rack. Now have "new" dishwasher. Great service by PartSelect.

I removed the inside cover of the door (6 to 8 screws), disconnected the wiring and wrote down where they needed to plug back into. Slipped the new dispenser door latch grommet over the latch, re-connected the wires, laid the door's inside cover back into place and replaced the screws. No leaks since. I have to say that without the help on partselect.com I would have wasted time and money in replacing the door's gasket. I'll definately check back here when any problem arises.

The repair went great. Very simple process to remove the old gasket and just press the new one in by hand. Total time to repair was 3 minutes. This was a very easy process, only needed to use a screw driver and my fingers to do it. The water leak was over. Anyone can do this repair. Don't think about getting a new dishwasher, or a plumber, as this is a very
simple repair that will easily do the fix!

I removed the gasket from the packaging & soaked it in hot water for approx 5 minutes to enhance the pliability of the rubber. I them opened the dishwasher door and removed the existing gasket, making sure I observed any specifics of the gasket, (ie...shape of gasket). I then cleaned any debris from the gasket channel. I took the new gasket from the water and folded it in half to determine where the middle was, and I started inserting the gasket beginning at the middle area of the channel, (just under the door latching mechanism). I finished inserting both sides and then closed the door for approximately 30 minutes to complete the gasket seating process. No leaks!!!

removed the 2 stops that held in the upper basket. rolled the old one out and slid the new one in. the replaced the stops. cake and pie!!

just pulled out old gasket
pushed in new one

After reading repair stories on this website, I decided to order the grommet as well as the seal for my dishwasher door. The seal was easy, just pull the old one out and push the new one in. Make sure the ends were even and that was done. Next came the grommet. 7 screws and I had the plastic off of the door. Then you just flip the plastic panel over and be careful of the wires.(I didn't remove them) Remove two more screws and the latch came out. Just tug the old grommet off and push the new one into place. Line it back up and replace the bolts. Flip the plastic back over and put the other 7 screws back in and you are ready to clean again. While I was in there I took a little extra time to clean some of the buildup out of the sealing surfaces. No more leaks!

watched the video instructions and followed them. ;Very easy.

Actually following the online video is the way to go.