CDT835SMJ4DS General Electric Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Leak pan was missing upon new installation
Due to the almost zero clearance between the recirculating pump and the floor, getting the pan to line up and engage the tabs on the dishwasher frame can seem to be an impossible task. I did accomplish the task as instructed in the owners installation manual once.
However, I observed that the leak was just a drop at a time only on the deep clean mode where water recycling was in constant use during a long wash cycle. So, I recommend to slide the pan in the relative position without trying to engage the tabs and you will still accomplish the reason for the leak pan. Remember, the purpose of the Leak Pan is to protect your floor, so use it the easy way as I am.
However, I observed that the leak was just a drop at a time only on the deep clean mode where water recycling was in constant use during a long wash cycle. So, I recommend to slide the pan in the relative position without trying to engage the tabs and you will still accomplish the reason for the leak pan. Remember, the purpose of the Leak Pan is to protect your floor, so use it the easy way as I am.
Parts Used:
-
Paul from ANGIER, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old Trim Tub Pieces were bent from an improper installation
I have them to the plumber who was reinstalling a poorly installed dishwasher. Parts worked perfectly
Parts Used:
-
Mark from BRUCE TWP, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right part wrong description
I had to replace a docking port. Parts Select had the part, labeled as stainless, just as this survey indicates. Well folks, the part I received is 100% plastic. It it the correct part, just not stainless. Should it have been stainless due to a faulty plastic design? I don’t know.
I used Parts Select for the simple directions for installation. I was eventually linked to a YouTube video for a completely different docking port. Does my part slip on? Does it press in? I don’t know.
Needless to say, this has been a cheap but frustrating ordeal that is not yet over. Thanks for having the stainless, but really plastic, part and for having directions for some other part available.
I used Parts Select for the simple directions for installation. I was eventually linked to a YouTube video for a completely different docking port. Does my part slip on? Does it press in? I don’t know.
Needless to say, this has been a cheap but frustrating ordeal that is not yet over. Thanks for having the stainless, but really plastic, part and for having directions for some other part available.
Parts Used:
-
Al from HILTON HEAD, SC
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher door sensor/ mother board
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
Parts Used:
-
Donald from NASHVILLE, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not shut, machine would not run.
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Parts Used:
-
Deborah from BRADENTON, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!