CDT725SSF2SS General Electric Dishwasher - Instructions

I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.

2 hose clamps, connect the wire with the wire adaptor suppled

Simply removed old gasket by hand, lined up center of new gasket (white dot was printed on the center of new gasket) with the tub latch and pressed new gasket into place. We have used the dishwasher about a dozen times since and hasn't leaked a drop.

I followed the U tube instructions already put out part select.

My granddaughter's fian'ce actially replaced the pump.
He pulled the dishwasher out, tipped it over and quickly and easily replaced the pump.
I had already snapped the converter on to the pump so it was ready to hook up. I had read previous messages that this part had a converter.
After putting the washer back in place we set it on a light wash to test it.
It went very well.

Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher

Followed the instructions on the video, it was pretty straight forward. It was helpful to know what to expect before hand like removing accumulated water in the drain before removing the flood switch so as not to have that water drain under the dishwasher. Knowing to have a nut driver with magnetic tip was helpful in removing and reinserting the screws. all in all it was pretty easy repair.

Had to trouble shoot to isolated the true fault condition. Checked heating element was good
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

I determined the guide rail on one side had broke when the white plastic bearings fell out of their track. I decided to replace both sides at the same time, so I ordered 2. They arrived quickly and I installed them and placed the middle rack back into the dishwasher. Went together fairly easily. I took pictures before removing the guides from the rack, so I would remember how to put the new ones back one when they arrived. Very happy with this DIY repair that easily would have taken much longer and would have been way more expensive! Thank you!

The part did not fit at all but not worth it to me to return it. The part I need is about 20 inches in length and the one sent was about 10 inches. I will simply call for this dishwasher to be repaired or replaced.

Bottom rack came complete with all racks. Only had to transfer the (2) side bumper guards,

The only directions that came with the new pump and filter, was how to replace the filter. I had to find a You Tube video to show me where the drain pump was located., and the way to get to it. I also had to figure out how the new pump was hooked up electrically, since the new pump did not work with the plug in on the machine.

Pulled washer out of space to access cables to the door. Removed moved the cables by stretching springs and unhooking cable from door. Disconnected wire from door to machine in body of machine. Opened door an lifed on an angle that allowed door to be lifted out of hinges. Unscrew and remove hinges on both sides. Remove by simply pulling them straight in direction of the bottom of the door. Then unscrew bolts on either side that are now exposed after taking hinges out. Then push inside of door up and remove. Unscrew the control board unit. Un plug cable to control board. Remove bezel cover. Then carefully unsnap unit case and remove board. Replace with the new board. However since this is a replacement part it must be configured for your machine. Instructions shou you the configuration. However where I ran into a problem was dining out how to set it. There were no switches. What I learned was that altouch it looked like one piece the jumper connections actually were four separate pieces that were tightly fitted together. In order to get the configuration you simply have to lift the jumper connector up. Once done reverse process and your done. If I did not run into that one issue repair time should be 30 minutes tops.

Followed directions on YouTube