CDT706P2M5S1 General Electric Dishwasher - Instructions

Started by removing dishwasher, including disconnecting power, water and drain line. Then turned washer on back. Electrical connector to old wash pump was a little tricky to remove as the release tab isn’t straightforward, I used a tiny screwdriver and jiggled it around till it came loose. The factory hose clamps (2) are crimped on, but if you can find the tail end you can work them loose with a screwdriver by prying the tail up from the body of the clamp. Once you have the electrical connector and the two clamps removed, the pump comes of easily with a twisting motion. The new wash motor came with new clamps (2 extra). When sliding the rubber boots on the new pump in place, it will require a twisting motion to position it correctly, make sure (I didn’t and had to go through the whole process twice) that the rubber boot is not folded under on the bottom where it’s hard to see. Tighten clamps carefully and don’t over tighten. Plug in electrical connector and you’re ready to reinstall dishwasher.

A noisy dishwasher and water coming from underneath was being caused by a torn hose that is factory connected to the diverter. It was a little difficult to see at first as the hose sits slightly kinked when in it's normal position. Access to the diverter involves removal of the circulation pump. I ordered a new diverter which comes with metal screw on clamps. The main difficulty in installing is the positioning and alignment of the diverter and pump. My first effort resulted in a ripping of the attached diverter hose as I attempted to secure. I ordered another diverter. This time I used a lubricant to allow movement of the connecting hoses and made sure to not overtighten the clamps. I used a small mirror to make sure that the various hoses sat properly. Alignment took a bit of time. I then gently tightened the hoses. I ran the dishwasher, and found a leak, meaning that I needed to tighten these clamps a bit more. This is a doable repair that needs patience. The dishwasher is now very quiet and runs great!

1. Turn off the water.
2. Turn off the power to the dishwasher.
3. Pulled out the dishwasher.
4. Tilted it forward and to the side with a bowl to collect the water at the bottom.
5. Carefully laid the dishwasher on its side
6. Removed the existing pump. Make note of its orientation before removing (maybe take a picture). Disconnect the wire and loosen the 2 pipe clamps used to attach the pump. The pipe clamps were not the adjustable, reusable kind but the replacement part came with several.
7. Put the new pipe clamps on the hoses (the supply and discharge side) so they're in place.
8. Installed the replacement pump by pushing it on to the supply then the discharge hoses.
9. Move the clamps into place and tighten.
10. Reconnect the power wire.
11. Stand the dishwasher up.
12. Turn on the power and water.
13. Run a quick test to make sure it's working and doesn't leak.
14. Push it back in to place and reattach it to the cabinets.

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

Shut off power at breaker, remove two screws anchoring DW to counter top . Slide DW out far enough to access door latch, disconnect electrical wiring plug, remove two Phillips head screws, install new door latch, repeat installation in reverse order.

My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine

Twist counter clockwise to remove clockwise to install

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.

Simply twist on the new part/filter.

Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight

Process of elimination and a visit to my local repair store told me it was wise to try the tub gasket, and according to partselect.com, it solved the problem a majority of the time. My local repair dealer agreed: Try it. They agreed because for them to replace a lower door gasket AND the $10 tub gasket... if they came out, the service call and parts would equal half the cost to replace the whole dishwasher. So I bought a tub gasket from partselect.com and replaced the old one. It worked, it was easy, so if your same make & model is leaking? Try it first. That's my advice.

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.

This is a replacement that is straightforward but a bit mechanical. For an experienced engineer it was no problem but for the common household this is a repair best left to the pros. Fixed the issue no problem and the dishwasher is working perfectly now.

Replaced old gasket with new one. More difficult than expected, because new gasket was much stiffer than old one. Also, the yellow centering spot on gasket (to line up with top latch) was nearly impossible to see. Unfortunately, this did not solve the problem for me, so money was wasted. Bought new dishwasher.